![](http://datasheet.mmic.net.cn/Exar-Corporation/XRT79L71IB-F_datasheet_100145/XRT79L71IB-F_63.png)
PRELIMINARY
XRT79L71
48
REV. P2.0.0
1-CHANNEL DS3/E3 CLEAR-CHANNEL FRAMERLIU COMBO - CC/HDLC ARCHITECTURE
3.1
General Flow of XRT79L71 ATM UNI/PPP/Clear-Channel DS3/E3 Framer Device Interrupt
Servicing
Whenever any of the conditions, presented in Table 7 occur (if their Interrupt is enabled), then the XRT79L71
will generate an interrupt request to the C/P by asserting the active-low interrupt request output pin, INT.
Shortly after the C/P has detected the activated INT signal, it will enter into the appropriate user-supplied
interrupt service routine. The first task, for the C/P, while running this interrupt service routine, may be to
isolate the source of the interrupt request down to the device level (e.g., the XRT79L71 ATM UNI/PPP/Clear-
Channel DS3/E3 Framer device), if multiple peripheral devices exist in the user's system.
However, once the interrupting peripheral device has been identified and determined to be the XRT79L71, the
next task for the C/P is to identify the functional block (within the XRT79L71) that requested the interrupt.
Finally, the C/P will need to proceed further and identify the exact condition(s) causing the interrupt to be
generated by the XRT79L71.
The procedure for servicing the XRT79L71 Interrupts is best achieved by executing the following steps.
STEP 1 - Determine the Functional Block(s) requesting the Interrupt
Framer Block Interrupt Enable Register
0x1104
Framer Block Interrupt Status Register
0x1105
RxDS3 Interrupt Enable RegisterRxE3 Interrupt Enable Register # 1 - ITU-T G.751RxE3 Interrupt
Enable Register # 1 - ITU-T G.832
0x1112
RxDS3 Interrupt Status RegisterRxE3 Interrupt Enable Register # 2 - ITU-T G.751RxE3 Interrupt
Enable Register # 2 - ITU-T G.832
0x1113
RxE3 Interrupt Status Register # 1 - ITU-T G.751RxE3 Interrupt Status Register # 1 - ITU-T G.832
0x1114
RxE3 Interrupt Status Register # 2 - ITU-T G.751RxE3 Interrupt Status Register # 2 - ITU-T G.832
0x1115
RxDS3 FEAC Interrupt Enable/Status Register
0x1117
RxDS3/E3 LAPD Control Register
0x1118
Transmit DS3 FEAC Configuration & Status Register
0x1131
Transmit DS3/E3 LAPD Status/Interrupt Register
0x1134
RxPLCP Interrupt Enable Register
0x1191
RxPLCP Interrupt Status Register
0x1192
LIU Interrupt Enable Register
0x1301
LIU Interrupt Status Register
0x1302
Receive ATM Cell Processor Block - Receive ATM Interrupt Status Register - Byte 1
0x170A
Receive ATM Cell Processor Block - Receive ATM Interrupt Status Register - Byte 0
0x170B
Receive ATM Cell Processor Block - Receive ATM Interrupt Enable Register - Byte 1
0x170E
Receive ATM Cell Processor Block - Receive ATM Interrupt Enable Register - Byte 0
0x170F
Transmit ATM Cell Processor Block - Transmit ATM Interrupt Status Register
0x1F0B
Transmit ATM Cell Processor Block - Transmit ATM Interrupt Enable Register
0x1F0F
TABLE 8: A LISTING OF THE XRT79L71 ATM UNI/PPP/CLEAR-CHANNEL DS3/E3 FRAMER DEVICE INTERRUPT
BLOCK REGISTERS - CLEAR-CHANNEL FRAMER APPLICATIONS
REGISTER
ADDRESS LOCATION