- 您現在的位置：買賣IC網 > PDF目錄379802 > CD1284 (Intel Corp.) IEEE 1284-Compatible Parallel Interface Controller with Two High-Speed Asynchronous Serial Ports PDF資料下載
參數資料
| 型號： | CD1284 |
| 廠商： | Intel Corp. |
| 英文描述： | IEEE 1284-Compatible Parallel Interface Controller with Two High-Speed Asynchronous Serial Ports |
| 中文描述： | 符合IEEE 1284兼容并行接口控制器兩個高速異步串行端口 |
| 文件頁數： | 141/176頁 |
| 文件大?。?/td> | 2255K |
| 代理商： | CD1284 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁當前第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁
IEEE 1284-Compatible Parallel Interface Controller
—
CD1284
Datasheet
141
7.7.9
Parallel FIFO Empty Pointer Register
This register holds the internal empty location pointer of the FIFO. It identifies the location in the
FIFO from which the next byte of data transfers from the FIFO.
Bit
Description
7
FIFO Reset:
This bit must be set together with the correct value of DMAdir to properly initialize the data
pipeline and FIFO registers for data transfer or when a new data transfer direction is desired. Any data
remaining in the FIFO is discarded. The FIFO remains in reset mode until this bit is cleared with a second
register write operation.
6
DMA Enable:
This bit must be set for DMA requests to move data to or from the FIFO to be made. When
DMAen
=
1, The PFQR quantity value is compared with the PFTR user-programmed threshold value. In
Receive mode, if the threshold is equalled or exceeded, DMAREQ* is asserted and causes DMA data
transfers of whole (2-byte) words from the FIFO by the data pipeline. In Transmit mode, if the amount of data
in the FIFO is equal to or less than the threshold, DMAREQ* is asserted causing DMA data transfers of whole
(2-byte) words to the FIFO by the data pipeline.
5
DMA Direction:
This bit sets the direction of transfer between the parallel FIFO and system memory. If
DMAdir
=
1, the direction is transmit (system memory to the parallel FIFO); if it is
‘
0
’
, the direction is receive.
The desired DMAdir value must be set together with FIFOres when initializing the FIFO logic for data transfer.
Once a DMAdir value is set and the FIFOres is complete, that DMAdir selection must be maintained during
any other changes to the control bits of the PFCR.
Note:
This bit sets the direction of the channel, even when DMA is not enabled. The proper direction must be
set regardless of the DMAen bit.
4
Interrupt Enable:
This is the master interrupt enable for the parallel channel. This bit must be set for any
interrupts generated by the data pipeline, parallel port, or error status. In Poll-mode operation, host software
toggles this bit to signal the completion of the service-acknowledge cycle. Toggling this bit updates the state
of SVCREQP* and the PIR according to the current state of PCISR, DERR, and PFSR. For this reason,
PCISR, DERR, and PFSR should be read and cleared at the end of the service routine to ensure that no
requests were skipped. This is because an edge-sensitive interrupt controller may not detect a request active
when the program returns from the service routine.
3
RLE Enable:
The state of this bit enables RLE encoding/decoding for the direction defined by DMAdir. The
RLEen bit effects the flow of data through the data pipeline in the transmit direction. Data flow into the FIFO is
managed in such a way that PFHR1 and PFHR2 are kept full to permit evaluation of data sequences for
possible compression. The effect is that following any data transfer while RLEen is set, the final 2 bytes
written to the DMABUF register are kept in PFHR1 and PFHR2. To allow these bytes to be moved into the
FIFO or to make room in PFHR1 for a tagged data transfer, RLEen must be
‘
0
’
and both DMAen and
DMAbufWe must be
‘
0
’
.
2
Set TAG:
This bit specifies that the next character written to the parallel channel by the PFHR1 register is to
be tagged as an ECP or EPP special character (for a detailed explanation of the special handling of these
characters, see
Section 5.13
). The setTAG bit is cleared by a write to PFHR1 thus, this bit must be set each
time a tagged character is to be written.
1
Error Interrupt Enable:
This bit enables a non-zero DataErr status to cause an interrupt if IntEn is also set.
0
DMA Buffer Write Enable:
This bit must be set to enable host writes to the DMABUF register. It also enables
the FIFO data pipeline to empty the DMABUF register when written to by the host system. In this case, the
system writes to the DMA buffer (without DMA transfers) providing a low-performance alternative to DMA
transfers.
Register Name: PFEP
Register Description: Parallel FIFO Empty Pointer
Access: Read/Write
Bit 7
Bit 6
0
0
8-Bit Hex Address: 39
Default Value: 00
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
6-bit binary FIFO Pointer Value
相關PDF資料 |
PDF描述 |
|---|---|
| CD13002 | NPN SILICON PLANAR EPITAXIAL, HIGH VOLTAGE FAST SWITCHING POWER TRANSISTOR |
| CD14538 | CMOS DUAL PRECISION MONOSTABLE MULTIVIBRATOR |
| CD14538BMS | CMOS Dual Precision Monostable Multivibrator |
| CD15B-15MB | CD105B |
| CD105B | CD105B |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CD-12AFFM-QL8D01 | 功能描述:MIDDLE 制造商:amphenol ltw 系列:* 零件狀態:在售 標準包裝:10 |
| CD-12AFFM-QR8D01 | 功能描述:MIDDLE 制造商:amphenol ltw 系列:* 零件狀態:在售 標準包裝:10 |
| CD-12AMMM-QL8D01 | 功能描述:MIDDLE 制造商:amphenol ltw 系列:* 零件狀態:在售 標準包裝:10 |
| CD-12BFFA-LL7001 | 功能描述:MIDDLE 制造商:amphenol ltw 系列:* 零件狀態:在售 標準包裝:10 |
| CD-12BFFA-QL8SP0 | 功能描述:CONN PLUG FMALE 12POS CRIMP 制造商:amphenol ltw 系列:X-Lok 包裝:散裝 零件狀態:在售 連接器類型:插頭，母型插口 針腳數:12（數據） 外殼尺寸 - 插件:C 外殼尺寸，MIL:- 安裝類型:自由懸掛 端接:壓接 緊固類型:推挽式 朝向:帶標記 侵入防護:IP68 - 防塵，防水 外殼材料，鍍層:聚酰胺（PA），尼龍，玻璃纖維增強型 觸頭鍍層:金 特性:后殼，應力消除 電壓 - 額定:- 額定電流:5A 觸頭鍍層厚度:- 工作溫度:-20°C ~ 80°C 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。