- 您現在的位置：買賣IC網 > PDF目錄379851 > CDK8920A (Cirrus Logic, Inc.) CRYSTAL LAN ISA PLUG-AND-PLAY ETHERNET CONTROLLER PDF資料下載
參數資料
| 型號： | CDK8920A |
| 廠商： | Cirrus Logic, Inc. |
| 英文描述： | CRYSTAL LAN ISA PLUG-AND-PLAY ETHERNET CONTROLLER |
| 中文描述： | 水晶藍的ISA即插即用，即插即用以太網控制器 |
| 文件頁數： | 86/144頁 |
| 文件大小： | 1229K |
| 代理商： | CDK8920A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁
5.0
OPERATION
5.1
the Interrupt Status Queue
Managing Interrupts and Servicing
The Interrupt Status Queue (ISQ) is used by the
CS8920A to communicate Event reports to the
host processor. Whenever an event occurs that
triggers an enabled interrupt, the CS8920A sets
the appropriate bit(s) in one of five registers,
maps the contents of that register to the ISQ, and
drives the selected interrupt request pin high (if
an earlier interrupt is waiting in the queue, the
interrupt request pin will already be high). When
the host services the interrupt, it must first read
the ISQ to learn the nature of the interrupt. It can
then process the interrupt (the first read to the
ISQ causes the interrupt request pin to go low.
Three of the registers mapped to the ISQ are
event registers: RxEvent (Register 4), TxEvent
(Register 8), and BufEvent (Register C). The
other two registers are counter-overflow reports:
RxMISS (Register 10) and TxCOL (Register 12).
There may be more than one RxEvent report
and/or more than one TxEvent report in the ISQ
at a time. However, there may be only one
BufEvent report, one RxMISS report and one
TxCOL report in the ISQ at a time.
Event reports stored in the ISQ are read out in
the order of priority, with RxEvent first, followed
by TxEvent, BufEvent, RxMiss, and then
TxCOL. The host only needs to read from one
location to get the interrupt currently at the front
of the queue. In Memory Mode, the ISQ is lo-
cated at PacketPage base + 0120h. In I/O Mode,
it is located at I/O base + 0008h. Each time the
host reads the ISQ, the bits in the corresponding
register are cleared and the next report in the
queue moves to the front.
When the host starts reading the ISQ, it must
read and process all Event reports in the queue.
A readout of a null word (0000h) indicates that
all interrupts have been read.
The ISQ is read as a 16-bit word. The lower six
bits (0 through 5) contain the register number (4,
8, C, 10, or 12). The upper ten bits (6 through F)
contain the register contents. The host must al-
ways read the entire 16-bit word, because the
CS8920A does not support 8-bit access to its in-
ternal registers. Figure 5.1 shows the operation
of the ISQ.
The active interrupt pin (INTRQx) is selected via
the Interrupt Number register (PacketPage base +
0370h). As an additional option, all of the inter-
rupt pins can be placed in the high-impedance
state using the same register. See Section 4.3.
An event triggers an interrupt only when the En-
ableIRQ bit of the Bus Control register (bit F of
register 17) is set.
After the CS8920A has generated an interrupt,
the first read of the ISQ makes the INTRQ out-
put pin go low (inactive). INTRQ remains low
until the null word (0000h) is read from the ISQ,
or for 1.6
μ
s, whichever is longer.
Typically, when interrupts have been enabled for
various error conditions (runt, CRC error, frame
> 1518 bytes) via register 3, the software will
also select that those frames be discarded (regis-
ter 5).
CS8920A
86
DS238PP2
相關PDF資料 |
PDF描述 |
|---|---|
| CDL13005 | NPN PLASTIC POWER TRANSISTOR |
| CDLL4150-1 | SWITCHING DIODE |
| CDLL4567A | Single Schmitt-Trigger Inverter 5-SOT-23 -40 to 85 |
| CDLL4568 | TEMPERATURE COMPENSATED ZENER REFERENCE DIODES |
| CDLL4568A | Single Schmitt-Trigger Inverter 5-SC70 -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDKEIL | 功能描述:開發軟件 Devel Software and Documention CD RoHS:否 制造商:Atollic Inc. 產品:Compilers/Debuggers 用于:ARM7, ARM9, Cortex-A, Cortex-M, Cortex-R Processors |
| CDKEIL-US | 功能描述:開發軟件 DEVELOPMENT SOFTWARE AND DOCUMENTATION CD RoHS:否 制造商:Atollic Inc. 產品:Compilers/Debuggers 用于:ARM7, ARM9, Cortex-A, Cortex-M, Cortex-R Processors |
| CDKWM1804-S-1 | 功能描述:WM1804 - Audio, Audio Processing Evaluation Board 制造商:cirrus logic inc. 系列:- 零件狀態:有效 主要用途:音頻，音頻處理 嵌入式:- 使用的 IC/零件:WM1804 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
| CDKWM1811A-S-1 | 功能描述:WM1811A - Audio, CODEC Evaluation Board 制造商:cirrus logic inc. 系列:- 零件狀態:有效 主要用途:音頻編解碼器 嵌入式:- 使用的 IC/零件:WM1811A 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
| CDKWM5102-S-1 | 功能描述:WM5102 - Audio, CODEC Evaluation Board 制造商:cirrus logic inc. 系列:- 零件狀態:有效 主要用途:音頻編解碼器 嵌入式:- 使用的 IC/零件:WM5102 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。