- 您現在的位置：買賣IC網 > PDF目錄384760 > MT9072 (Mitel Networks Corporation) Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 PDF資料下載
參數資料
| 型號： | MT9072 |
| 廠商： | Mitel Networks Corporation |
| 元件分類： | 通信及網絡 |
| 英文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 中文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 文件頁數： | 73/269頁 |
| 文件大?。?/td> | 778K |
| 代理商： | MT9072 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁當前第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁
Advance Information
MT9072
73
The least significant bit of the Transmit FIFO data is sent first on the serial stream.
Frame aborts (the transmission of 7F hex), are transmitted by tagging a byte previously written to the Tx FIFO.
When a byte has an FA tag, then an FA is sent instead of that tagged byte. That is, all bytes previous to but not
including that byte are sent. After a Frame Abort, the transmitter returns to the Mark Idle or Interframe Time Fill
state, depending on the state of the Mark idle control bit.
Tx FIFO underrun will occur if the FIFO empties and the last byte did not have either an EOP or FA tag. A
frame abort sequence will be sent when an underrun occurs.
Below is an example of the transmission of a three byte packet (’AA’ ’03’ ’77’ hex) (Interframe time fill). TXcen
can be enabled before or after this sequence.
(a) Write’0020’hex to Control Register 1
(b) Write’AA’ hex to TX FIFO
(c) Write’03’hex to TX FIFO
(d) Write’01A0’ hex to Control Register 1
(e) Write’77’hex to TX FIFO
The transmitter may be enabled independently of the receiver. This is done by setting the TXEN bit of the
Control Register YF2. Enabling happens immediately upon writing to the register. Disabling using TXen will
occur after the completion of the transmission of the present packet; the contents of the FIFO are not cleared.
Disabling will consist of stopping the transmitter clock. The Status and Interrupt Registers may still be read and
the FIFO and Control Registers may be written to while the transmitter is disabled. The transmitted FCS may
be inhibited using the Tcrci bit of HDLC Master Control Register. In this mode the opening flag followed by the
data and closing flag is sent and zero insertion still included, but no CRC. That is, the FCS is injected by the
microprocessor as part of the data field. This is used in V.120 terminal adaptation for synchronous protocol
sensitive UI frames.
-Mark idle bit set
-Data byte
-Data byte
-TXEN; EOP; Mark idle bits set
-Final data byte
8.1.9
After initialization and enabling, the receiver clocks in serial data, continuously checking for Go-aheads (0 1111
1110), flags (0111 1110), and Idle Channel states (at least fifteen ones). When a flag is detected, the receiver
synchronizes itself to the serial stream of data bits, automatically calculating the FCS. If the data length
between flags after zero removal is less than 25 bits, then the packet is ignored so no bytes are loaded into Rx
FIFO. When the data length after zero removal is between 25 and 31 bits, a first byte and bad FCS code are
loaded into the Rx FIFO (see definition of RQ8 and RQ9 below).
HDLC Receiver
If address recognition is required, the Receiver Address Recognition Registers are loaded with the desired
address and the Adrec bit in the HDLC Control Register is set high(YF2). Bit 0 and 8 of the Address Register
are used as enable bits for their respective byte, thus allowing either or both of the first two bytes to be
compared to the expected values. Bit 0 of the first byte of the address received (address extension bit) will be
monitored to determine if a single or dual byte address is being received. If this bit is 0 then a two byte address
is being received and then only the first six bits of the first address byte are compared. An all call condition is
also monitored for the second address byte; and if received the first address byte is ignored (not compared with
mask byte). If the address extension bit is a 1 then a single byte address is being received. In this case, an all
call condition is monitored for in the first byte as well as the mask byte written to the comparison register and
the second byte is ignored. Seven bits of address comparison can be realized on the first byte if this is a single
byte address by setting the Seven bit of HDLC control register(YF2).
T
he following two Status Register bits (RQ8 and RQ9) are appended to each data byte as it is written to the Rx
FIFO. They indicate that a good packet has been received (good FCS and no frame abort), or a bad packet
with either incorrect FCS or frame abort. The Status and Interrupt Registers should be read before reading the
Rx FIFO since Status and Interrupt information correspond to the byte at the output of the FIFO (i.e. the byte
about to be read). The Status Register bits are encoded as follow
s:
RQ9
1
0
1
0
RQ8
1
1
0
0
Byte status
last byte (bad packet)
first byte
last byte (good packet)
packet byte
相關PDF資料 |
PDF描述 |
|---|---|
| MT90820 | Large Digital Switch(大數字開關) |
| MT90823 | 3V Large Digital Switch(3V 大數字開關) |
| MT90826 | Quad Digital Switch(四數字開關) |
| MT90840 | Distributed Hyperchannel Switch(分布式超級通道開關) |
| MT90863AL1 | 3V Rate Conversion Digital Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9072AB | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Octal T1/E1/J1 Framer |
| MT9072AV | 制造商:Microsemi Corporation 功能描述:FRAMER E1/J1/T1 3.3V 256BGA - Trays 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 256BGA - Trays |
| MT9072AV2 | 制造商:Microsemi Corporation 功能描述:FRAMER E1/J1/T1 3.3V 220BGA - Trays 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 220BGA - Trays |
| MT90732 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS E2/E3 Framer (E2/E3F) |
| MT90732AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS E2/E3 Framer (E2/E3F) |
發布緊急采購，3分鐘左右您將得到回復。