- 您現在的位置：買賣IC網 > PDF目錄1961 > PI7C8140AMAE (Pericom)IC PCI-PCI BRIDGE 2PORT 128-QFP PDF資料下載
參數資料
| 型號： | PI7C8140AMAE |
| 廠商： | Pericom |
| 文件頁數： | 18/82頁 |
| 文件大小： | 0K |
| 描述： | IC PCI-PCI BRIDGE 2PORT 128-QFP |
| 標準包裝： | 39 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-QFP（14x20） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
PI7C8140A
2-PORT PCI-TO-PCI BRIDGE
Page 25 of 82
March 20, 2007 – Revision 1.01
accessed. In addition, the bus number in Type 1 transactions specifies the PCI bus to which the
transaction is targeted.
2.7.1
TYPE 0 ACCESS TO PI7C8140A
The configuration space is accessed by a Type 0 configuration transaction on the primary interface. The
configuration space cannot be accessed from the secondary bus. The bridge responds to a Type 0
configuration transaction by asserting P_DEVSEL# when the following conditions are met during the
address phase:
The bus command is a configuration read or configuration write transaction.
Lowest two address bits P_AD[1:0] must be 00b.
Signal P_IDSEL must be asserted.
The bridge limits all configuration access to a single DWORD data transfer and returns target-
disconnect with the first data transfer if additional data phases are requested. Because read transactions
to configuration space do not have side effects, all bytes in the requested DWORD are returned,
regardless of the value of the byte enable bits.
Type 0 configuration write and read transactions do not use data buffers; that is, these transactions are
completed immediately, regardless of the state of the data buffers. The bridge ignores all Type 0
transactions initiated on the secondary interface.
2.7.2
TYPE 1 TO TYPE 0 CONVERSION
Type 1 configuration transactions are used specifically for device configuration in a hierarchical PCI
bus system. A PCI-to-PCI bridge is the only type of device that should respond to a Type 1
configuration command. Type 1 configuration commands are used when the configuration access is
intended for a PCI device that resides on a PCI bus other than the one where the Type 1 transaction is
generated.
The bridge performs a Type 1 to Type 0 translation when the Type 1 transaction is generated on the
primary bus and is intended for a device attached directly to the secondary bus. The bridge must convert
the configuration command to a Type 0 format so that the secondary bus device can respond to it. Type
1 to Type 0 translations are performed only in the downstream direction; that is, the bridge generates a
Type 0 transaction only on the secondary bus, and never on the primary bus.
The bridge responds to a Type 1 configuration transaction and translates it into a Type 0 transaction on
the secondary bus when the following conditions are met during the address phase:
The lowest two address bits on P_AD[1:0] are 01b.
The bus number in address field P_AD[23:16] is equal to the value in the secondary bus number
register in configuration space.
The bus command on P_CBE[3:0] is a configuration read or configuration write transaction.
When the bridge translates the Type 1 transaction to a Type 0 transaction on the secondary
interface, it performs the following translations to the address:
Sets the lowest two address bits on S_AD[1:0].
Decodes the device number and drives the bit pattern specified in Table 2-6 on S_AD[31:16] for
the purpose of asserting the device’s IDSEL signal.
Sets S_AD[15:11] to 0.
07-0067
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C8150ANDE | IC PCI-PCI BRIDGE 2PORT 256-PBGA |
| PI7C8150BNDIE | IC PCI-PCI BRIDGE ASYNC 256-PBGA |
| PI7C8152BMAIE | IC PCI-PCI BRIDGE 2PORT 160-MQFP |
| PI7C8154ANAE | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| PI7C8154BNAIE | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8148A | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2-PORT PCI-TO-PCI BRIDGE ADVANCE INFORMATION |
| PI7C8148AEVB | 功能描述:界面開發工具 64B/66MHz 2 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| PI7C8148ANBE | 功能描述:外圍驅動器與原件 - PCI 2-Port PCI-to-PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8148ANJ | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2-PORT PCI-TO-PCI BRIDGE ADVANCE INFORMATION |
| PI7C8148ANJE | 功能描述:外圍驅動器與原件 - PCI 2-Port PCI-to-PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。