參數資料
型號: TMX320C6412GNZ
廠商: Texas Instruments, Inc.
英文描述: Signal Processor
中文描述: 信號處理器
文件頁數: 100/159頁
文件大小: 1989K
代理商: TMX320C6412GNZ
Power-Down Modes Logic
100
April 2003 Revised June 2004
SPRS219D
Table 212. Characteristics of the Power-Down Modes
PRWD FIELD
(BITS 1510)
POWER-DOWN
MODE
WAKE-UP METHOD
EFFECT ON CHIP’S OPERATION
000000
No power-down
001001
PD1
Wake by an enabled interrupt
CPU halted (except for the interrupt logic)
Power-down mode blocks the internal clock inputs at the
boundary of the CPU, preventing most of the CPU’s logic from
switching. During PD1, EDMA transactions can proceed between
peripherals and internal memory.
010001
PD1
Wake by an enabled or
non-enabled interrupt
011010
PD2
Wake by a device reset
Output clock from PLL is halted, stopping the internal clock
structure from switching and resulting in the entire chip being
halted. All register and internal RAM contents are preserved. All
functional I/O “freeze” in the last state when the PLL clock is
turned off.
011100
PD3
Wake by a device reset
Input clock to the PLL stops generating clocks. All register and
internal RAM contents are preserved. All functional I/O “freeze” in
the last state when the PLL clock is turned off. Following reset, the
PLL needs time to re-lock, just as it does following power-up.
Wake-up from PD3 takes longer than wake-up from PD2 because
the PLL needs to be re-locked, just as it does following power-up.
All others
When entering PD2 and PD3, all functional I/O remains in the previous state. However, for peripherals which are asynchronous in nature or
peripherals with an external clock source, output signals may transition in response to stimulus on the inputs. Under these conditions,
peripherals will not operate according to specifications.
Reserved
2.20.2
C64x Power-Down Mode with an Emulator
If user power-down modes are programmed, and an emulator is attached, the modes will be masked to allow
the emulator access to the system. This condition prevails until the emulator is reset or the cable is removed
from the header. If power measurements are to be performed when in a power-down mode, the emulator cable
should be removed.
When the DSP is in power-down mode PD2 or PD3, emulation logic will force any emulation execution
command (such as Step or Run) to spin in IDLE. For this reason, PC writes (such as loading code) will fail.
A DSP reset will be required to get the DSP out of PD2/PD3.
相關PDF資料
PDF描述
TMX320VC5421 DIGITAL SIGNAL PROCESSOR
TMX320VC5509AGHH TMS320VC5509A Fixed-Point Digital Signal Processor
TMX470R1A64PN 16/32-Bit RISC Flash Microcontroller
TMXT504 SAW BANDPASS FILTER
TN0104 N-Channel Enhancement-Mode Vertical DMOS FET(擊穿電壓40V,低門限1.6V,N溝道增強型垂直DMOS結構場效應管)
相關代理商/技術參數
參數描述
TMX320C6412ZDK 制造商:Texas Instruments 功能描述:
TMX320C6413GTS 制造商:Texas Instruments 功能描述:
TMX320C6413GTS400 制造商:TI 制造商全稱:Texas Instruments 功能描述:Fixed-Point Digital Signal Processors
TMX320C6413GTS500 制造商:TI 制造商全稱:Texas Instruments 功能描述:Fixed-Point Digital Signal Processors
TMX320C6413GTSA400 制造商:TI 制造商全稱:Texas Instruments 功能描述:Fixed-Point Digital Signal Processors