- 您現在的位置：買賣IC網 > PDF目錄1961 > PI7C8154ANAE (Pericom)IC PCI-PCI BRIDGE ASYNC 304-PBGA PDF資料下載
參數資料
| 型號： | PI7C8154ANAE |
| 廠商： | Pericom |
| 文件頁數： | 80/114頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| 標準包裝： | 27 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 304-BBGA |
| 供應商設備封裝： | 304-PBGA（31x31） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
PI7C8154A
ASYNCHRONOUS 2-PORT
PCI-to-PCI BRIDGE
Advance Information
Page 68 of 114
DEC 2009 REVISION 1.02
8.1
GPIO CONTROL REGISTERS
During normal operation, the following device specific configuration registers control the GPIO
interface:
The GPIO output data register
The GPIO output enable control register
The GPIO input data register
These registers consist of five 4-bit fields:
Write-1-to-set output data field
Write-1-to-clear output data field
Write-1-to-set signal output enable control field
Write-1-to-clear signal output enable control field
Input data field
The bottom four bits of the output enable fields control whether each GPIO signal is input only or
bi-directional. Each signal is controlled independently by a bit in each output enable control field.
If a 1 is written to the write-1-to-set field, the corresponding pin is activated as an output. If a 1 is
written to the write-1-to-clear field, the output driver is tri-stated, and the pin is then input only.
Writing zeroes to these registers has no effect. The reset for these signals is input only.
The input data field is read only and reflects the current value of the GPIO pins. A type 0
configuration read operation to this address is used to obtain the values of these pins. All pins can
be read at any time, whether configured as input only or as bi-directional.
The output data fields also use the write-1-to-set and write-1-to-clear mode. If a 1 is written to the
write-1-to-set field and the pin is enabled as an output, the corresponding GPIO output is driven
HIGH. If a 1 is written to the write-1-to-clear field and the pin is enabled as an output, the
corresponding GPIO output is driven LOW. Writing zeros to these registers has no effect. The
value written to the output register will be driven only when the GPIO signal is configured as bi-
directional. A type 0 configuration write operation is used to program these fields. The rest value
for the output is 0.
8.2
SECONDARY CLOCK CONTROL
The PI7C8154A uses the GPIO pins and the MSK_IN signal to input a 16-bit serial data stream.
This data stream is shifted into the secondary clock control register and is used for selectively
disabling secondary clock outputs.
The serial data stream is shifted in as soon as P_RESET# is detected deasserted and the secondary
reset signal, S_RESET#, is detected asserted. The deassertion of S_RESET# is delayed until the
PI7C8154A completes shifting in the clock mask data, which takes 23 clock cycles. After that, the
GPIO pins can be used as general-purpose I/O pins.
An external shift register should be used to load and shift the data. The GPIO pins are used for shift
register control and serial data input. Table 8-1 shows the operation of the GPIO pins.
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C8154BNAIE | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| PI7C9X110BNBE | IC PCIE TO PCI REV BRG 160LFBGA |
| PI7C9X130DNDE | IC PCIE-PCIX BRIDGE 1PORT 256BGA |
| PI7C9X20303SLCFDE | IC PCIE PACKET SWITCH 128LQFP |
| PI7C9X20303ULAZPE | IC PCIE PACKET SWITCH 132TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8154ANAE-33 | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154B | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2 PORT 64 BIT 66MHZ PCI TO PCI BRIDGE |
| PI7C8154BNA | 制造商:Pericom Semiconductor Corporation 功能描述: |
| PI7C8154BNAE | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154BNAE-80 | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。