- 您現在的位置：買賣IC網 > PDF目錄1961 > PI7C8154ANAE (Pericom)IC PCI-PCI BRIDGE ASYNC 304-PBGA PDF資料下載
參數資料
| 型號： | PI7C8154ANAE |
| 廠商： | Pericom |
| 文件頁數： | 25/114頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| 標準包裝： | 27 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 304-BBGA |
| 供應商設備封裝： | 304-PBGA（31x31） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
PI7C8154A
ASYNCHRONOUS 2-PORT
PCI-to-PCI BRIDGE
Advance Information
Page 18 of 112
DEC 2009 REVISION 1.02
Name
Pin #
Type
Description
S_CLKIN
J4
I
Secondary Clock Input: Provides timing for all
transactions on the secondary interface.
S_CLKOUT[9:0]
P1, P2, P3, N1, N3, M2,
M1, M3, L3, L2
O
Secondary Clock Output: Provides secondary
clocks phase synchronous with the P_CLK.
When these clocks are used, one of the clock
outputs must be fed back to S_CLKIN. Unused
outputs may be disabled by:
1. Writing the secondary clock disable bits in the
configuration space
2. Using the serial disable mask using the GPIO pins
and MSK_IN
3. Terminating them electrically.
1.2.6
MISCELLANEOUS SIGNALS
Name
Pin #
Type
Description
MSK_IN
R21
I
Secondary Clock Disable Serial Input: This pin is
used by bridge to disable secondary clock outputs.
The serial stream is received by MSK_IN, starting
when P_RESET is detected deasserted and
S_RESET# is detected as being asserted. The serial
data is used for selectively disabling secondary
clock outputs and is shifted into the secondary clock
control configuration register. This pin can be tied
LOW to enable all secondary clock outputs or tied
HIGH to drive all the secondary clock outputs
HIGH.
P_VIO
R20
I
Primary I/O Voltage: This pin is used to determine
either 3.3V or 5V signaling on the primary bus.
P_VIO must be tied to 3.3V only when all devices
on the primary bus use 3.3V signaling. Otherwise,
P_VIO is tied to 5V.
S_VIO
N22
I
Secondary I/O Voltage: This pin is used to
determine either 3.3V or 5V signaling on the
secondary bus. S_VIO must be tied to 3.3V only
when all devices on the secondary bus use 3.3V
signaling. Otherwise, S_VIO is tied to 5V.
BPCCE
R4
I
Bus/Power Clock Control Management Pin:
When this pin is tied HIGH and the bridge is placed
in the D2 or D3HOT power state, it enables the bridge
to place the secondary bus in the B2 power state.
The secondary clocks are disabled and driven to 0.
When this pin is tied LOW, there is no effect on the
secondary bus clocks when the bridge enters the D2
or D3HOT power state.
CONFIG66
R22
I
66MHz Configuration: This pin indicates if the
bridge is capable of running at 66MHz operation.
Tie HIGH to set bit [21] of offset 04h of the status
register.
PMEENA#
D11
I
Power Management Enable Support: This pin
sets bits [31:27] offset DEh of the Power
Management Capabilities Register.
When tied
LOW, bits [31:27] offset DEh are set to 11111 to
indicate that the secondary devices are capable of
asserting PME#. When this pin is tied HIGH, bits
[31:27] offset DEh are set to 00000 to indicate
that PI7C8154A does not support the PME# pin.
For Intel 21154, this pin is defined as VDD. For
more info, please refer to Appendix on page 113.
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C8154BNAIE | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| PI7C9X110BNBE | IC PCIE TO PCI REV BRG 160LFBGA |
| PI7C9X130DNDE | IC PCIE-PCIX BRIDGE 1PORT 256BGA |
| PI7C9X20303SLCFDE | IC PCIE PACKET SWITCH 128LQFP |
| PI7C9X20303ULAZPE | IC PCIE PACKET SWITCH 132TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8154ANAE-33 | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154B | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2 PORT 64 BIT 66MHZ PCI TO PCI BRIDGE |
| PI7C8154BNA | 制造商:Pericom Semiconductor Corporation 功能描述: |
| PI7C8154BNAE | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154BNAE-80 | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。