- 您現在的位置：買賣IC網 > PDF目錄1961 > PI7C8154ANAE (Pericom)IC PCI-PCI BRIDGE ASYNC 304-PBGA PDF資料下載
參數資料
| 型號： | PI7C8154ANAE |
| 廠商： | Pericom |
| 文件頁數： | 22/114頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| 標準包裝： | 27 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 304-BBGA |
| 供應商設備封裝： | 304-PBGA（31x31） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
PI7C8154A
ASYNCHRONOUS 2-PORT
PCI-to-PCI BRIDGE
Advance Information
Page 15 of 112
DEC 2009 REVISION 1.02
Name
Pin #
Type
Description
P_REQ64#
AC14
STS
Primary 64-bit Transfer Request: P_REQ64# is
asserted by the initiator to indicate that the initiator
is requesting a 64-bit data transfer. P_REQ64# has
the same timing as P_FRAME#. When P_REQ64#
is asserted LOW during reset, a 64-bit data path is
supported. When P_REQ64# is HIGH during reset,
bridge drives P_AD[63:32], P_CBE[7:4], and
P_PAR64 to valid logic levels. When deasserting,
P_REQ64# is driven to a deasserted state for 1 cycle
and then sustained by an external pull-up resistor.
P_ACK64#
AB14
STS
Primary 64-bit Transfer Acknowledge:
P_ACK64# is asserted by the target only when
P_REQ64# is asserted by the initiator to indicate the
target’s ability to transfer data using 64 bits.
P_ACK64# has the same timing as P_DEVSEL#.
When deasserting, P_ACK64# is driven to a
deasserted state for 1 cycle and then is sustained by
an external pull-up resistor.
1.2.3
SECONDARY BUS INTERFACE SIGNALS
Name
Pin #
Type
Description
S_AD[31:0]
C3, A3, B3, C4, A4, B4, C5,
B5, A6, A7, D7, B7, A8,
B8, C8, A9, C13, B13, A13,
D13, C14, B14, C15, B15,
C16, B16, C17, B17, D17,
A17, B18, A18
TS
Secondary Address/Data: Multiplexed address and
data bus. Address is indicated by S_FRAME#
assertion. Write data is stable and valid when
S_IRDY# is asserted and read data is stable and
valid when S_IRDY# is asserted. Data is
transferred on rising clock edges when both
S_IRDY# and S_TRDY# are asserted. During bus
idle, bridge drives S_AD[31:0] to a valid logic level
when S_GNT# is asserted respectively.
S_CBE[3:0]
C6, D9, C12, A15
TS
Secondary Command/Byte Enables: Multiplexed
command field and byte enable field. During
address phase, the initiator drives the transaction
type on these pins. The initiator then drives the byte
enables during data phases. During bus idle, bridge
drives S_CBE[3:0] to a valid logic level when the
internal grant is asserted.
S_PAR
B12
TS
Secondary Parity: S_PAR is an even parity of
S_AD[31:0] and S_CBE[3:0] (i.e. an even number
of 1’s). S_PAR is valid and stable one cycle after
the address phase (indicated by assertion of
S_FRAME#) for address parity. For write data
phases, S_PAR is valid one clock after S_IRDY# is
asserted. For read data phase, S_PAR is valid one
clock after S_TRDY# is asserted. Signal S_PAR is
tri-stated one cycle after the S_AD lines are tri-
stated. During bus idle, bridge drives S_PAR to a
valid logic level when the internal grant is asserted.
S_FRAME#
B9
STS
Secondary FRAME (Active LOW): Driven by the
initiator of a transaction to indicate the beginning
and duration of an access. The de-assertion of
S_FRAME# indicates the final data phase requested
by the initiator. Before being tri-stated, it is driven
to a de-asserted state for one cycle.
S_IRDY#
C9
STS
Secondary IRDY (Active LOW): Driven by the
initiator of a transaction to indicate its ability to
complete current data phase on the secondary side.
Once asserted in a data phase, it is not de-asserted
until the end of the data phase. Before tri-stated, it
is driven to a de-asserted state for one cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C8154BNAIE | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| PI7C9X110BNBE | IC PCIE TO PCI REV BRG 160LFBGA |
| PI7C9X130DNDE | IC PCIE-PCIX BRIDGE 1PORT 256BGA |
| PI7C9X20303SLCFDE | IC PCIE PACKET SWITCH 128LQFP |
| PI7C9X20303ULAZPE | IC PCIE PACKET SWITCH 132TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8154ANAE-33 | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154B | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2 PORT 64 BIT 66MHZ PCI TO PCI BRIDGE |
| PI7C8154BNA | 制造商:Pericom Semiconductor Corporation 功能描述: |
| PI7C8154BNAE | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154BNAE-80 | 功能描述:外圍驅動器與原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。