參數資料
型號： OMAP5910(DSP)
英文描述： Dual-Core Processor
中文描述： 雙核處理器
文件頁數： 121/160頁
文件大小： 1997K
代理商： OMAP5910(DSP)
Electrical Specifications
109
August 2002 Revised August 2003
SPRS197B
Table 53. 32-kHz Input Clock Timing Requirements
NO.
MIN
NOM
MAX
UNIT
CK1
tcyc
tf
tr
Frequency
32.768
kHz
CK2
Fall time
25
ns
CK3
Rise time
25
ns
CK4
Duty cycle (high-to-low ratio)
30%
70%
%
CK5
Frequency stability
70
70
ppm
CK1
CK2
CK3
CLK32K_IN
Figure 53. 32-kHz Input Clock
5.6.2 Base Oscillator (12 MHz or 13 MHz) and Input Clock
The internal base system oscillator is enabled following a device reset. The oscillator requires an external
crystal to be connected across the OSC1_IN and OSC1_OUT pins. If the internal oscillator is not used
(configured in software), an external clock source must be applied to the OSC1_IN pin and the OSC1_OUT
pin must be left unconnected. Because the internal oscillator can be used as a clock source to the OMAP
DPLL, the 12- or 13-MHz crystal oscillation frequency can be multiplied to generate the DSP clock, MPU clock,
traffic controller clock.
The crystal must be in fundamental-mode operation, and parallel resonant, with a maximum effective series
resistance of 60
maximum. The connection of the required circuit, consisting of the crystal and two load
capacitors, is shown in Figure 54. The load capacitors, C
1
and C
2
, must be chosen such that the equation
below is satisfied (recommended values are C
1
= C
2
= 10 pF). C
L
in the equation is the load specified for the
crystal. All discrete components used to implement the oscillator circuit must be placed as close as possible
to the associated oscillator pins (OSC1_IN and OSC1_OUT) and to the V
SS
pins closest to the oscillator pins
(GZG balls AA1/Y3 or GDY balls E13/K9).
NOTE:
The base oscillator is powered by the CV
DD
supply. If an external clock source is used instead of using
the on-chip oscillator, care must be taken that the voltage level driven onto the OSC1_IN pin is no greater than
the CV
DD
voltage level.
C
1
C
2
(
C
1
C
L
C
2
)
OSC1_IN
OSC1_OUT
C1
C2
12 or 13 MHz crystal
Figure 54. Internal System Oscillator External Crystal
相關PDF資料
PDF描述
OMAP5910(RISC) Dual-Core Processor
OMC506 Closed Loop Speed Controller For 3-Phase Brushless DC Motor MP-3T Package
OMC507 5 Amp. Push-Pull 3-Phase Brushless DC Motor Controller Driver(5A,推挽三相無刷直流電機控制驅動器)
OMC510 36V Hi-Rel Three-Phase Brushless DC Motor Controller in a PCB-1 package
OMC510 DSP-Based Three-Phase Brushless DC Motor Controller(基于DSP的三相無刷直流電機控制器)
相關代理商/技術參數
參數描述
OMAP5910GGZG1 制造商:Rochester Electronics LLC 功能描述:- Bulk
OMAP5910GGZG2 制造商:Rochester Electronics LLC 功能描述:- Bulk
OMAP5910JGDY1R 功能描述:IC OMAP DUAL-CORE PROC 289-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:OMAP-59xx 標準包裝:60 系列:SCC 處理器類型:Z380 特點:全靜電 Z380 CPU 速度:20MHz 電壓:5V 安裝類型:表面貼裝 封裝/外殼:144-LQFP 供應商設備封裝:144-LQFP 包裝:托盤
OMAP5910JGDY2 功能描述:數字信號處理器和控制器 - DSP, DSC Applications Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
OMAP5910JGZG1 制造商:Texas Instruments 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*