- 您現在的位置：買賣IC網 > PDF目錄379804 > CD2481 (Intel Corp.) Programmable Four-Channel Communications Controller PDF資料下載
參數資料
| 型號： | CD2481 |
| 廠商： | Intel Corp. |
| 英文描述： | Programmable Four-Channel Communications Controller |
| 中文描述： | 可編程四通道通信控制器 |
| 文件頁數： | 85/222頁 |
| 文件大?。?/td> | 974K |
| 代理商： | CD2481 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁
Programmable Four-Channel Communications Controller
—
CD2481
Datasheet
85
to the threshold being exceeded. For this reason, the user should not use the Send Special Character
command in the STCR (Special Transmit Command register) to send XON/XOFF characters
because the CD2481 does not keep track of flow control characters that it did not send
automatically. The result could cause confusion on the other end of the connection due to
conflicting flow control commands.
Automatic in-band flow control is functional only in standard Async and Async-HDLC/PPP
modes; SLIP and MNP 4 expressly forbid in-band flow control. See the COR5 description for
programming details.
7.5.3
Out-of-Band Flow Control
Receive out-of-band flow control is enabled when the CTS Automatic Enable (CtsAE) bit
(COR2[1]) is set to 1. In this mode, character transmission begins only after the CTS* pin is active
(low). In asynchronous transmission, if CTS* goes inactive (high) after transmission has started,
the channel stops transmission after the current character in the Transmit Shift register, and the
current character in the Transmit Holding register are transmitted. In synchronous modes, if CTS*
goes inactive, the channel will stop transmission after the current frame. In either case,
transmission will restart after CTS* becomes active again.
The CD2481 can automatically flow control the remote device via the DTR* pin. This mode is
selected by setting a non-zero DTR* threshold in COR5 (COR5[3:0]; when both thresholds in
COR4[3:0] and the threshold in COR5 are exceeded, the CD2481 will set the DTR* pin high.
When the data in the FIFO falls below the DTR* threshold, the DTR* pin is automatically driven
low.
Each channel of the CD2481 has four pins that can be used either as a modem control or general-
purpose input/output pins. The modem signal names assigned to these four pins have been chosen
to provide an easy reference for system designers. In fact, they are all simply general-purpose
inputs and outputs (if automatic out-of-band flow-control is not used) that can be individually
controlled or examined via the modem signal value register(s). Since the pins are general-purpose,
system designers may choose to connect the pins in a manner that suits the application.
However, when the system software design employs automatic out-of-band flow control with the
pins, then the signal naming convention no longer holds true in some cases, depending on whether
the device is used as DCE or DTE. In this case, it is best to think of the pins in terms of their actual
uses within the CD2481 and connect them accordingly, without regard to their names. The RTS*
and CTS* pins are associated with transmitter and the DTR* and DSR* pins are associated with the
receiver. The table below shows Intel recommended signal hook-up if automatic, out-of-band flow
control is desired.
For example, if the CD2481 is designed to be DCE and automatic out-of-band flow control is
desired, the pin DTR should be connected to remote CTS input. If the CD2481 is to be used as the
DTE side, then the CD2481 CTS output would be connected to the remote CTS input.
Mode
CD2481
Pin Name
Out-of-Band
Flow Control
DCE
DTE
CTS
DTR
Signal remote to transmit
RTS
Not implemented in this direction
RTS
RTS
Request remote permission to transmit
CTS
CTS
Enable transmitter
相關PDF資料 |
PDF描述 |
|---|---|
| CD3086 | General Purpose NPN Transistor Array |
| CD4000 | CMOS NOR Gates |
| CD4001 | CMOS NOR Gates |
| CD4002 | CMOS NOR Gates |
| CD40011 | Quad 2-Input NOR,NAND Buffered B Series Gate |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CD24B3 031573 | 制造商:Comair Rotron 功能描述:FAN 254MM 24VDC |
| CD24B3 | 制造商:Comair Rotron 功能描述:FAN 254MM 24VDC |
| CD-250 | 制造商:Stellar Labs 功能描述:CD / USB Media Player with FM Tuner - MP3 and WMA |
| CD2500R1 | 制造商:LOGETR 功能描述: |
| CD250-3KVM.25 | 制造商:Yageo / Phycomp 功能描述:CD250-3KVM.25 |
發布緊急采購，3分鐘左右您將得到回復。