參數資料
型號： EVAL-ADUC7039QSPZ
廠商： Analog Devices Inc
文件頁數： 8/92頁
文件大小： 0K
描述： BOARD EVAL FOR ADUC7039
設計資源： ADuC7039QSPZ Gerber Files
EVAL-ADuC7039 Schematic & Brd Outline
標準包裝： 1
系列： QuickStart™ PLUS 套件
類型： MCU
適用于相關產品： ADuC7039
所含物品： 板
ADuC7039
Data Sheet
Rev. D | Page 16 of 92
The remap command must be executed from the absolute
Flash/EE address, and not from the mirrored, remapped
segment of memory, because this may be replaced by SRAM. If
a remap operation is executed while operating code from
the mirrored location, prefetch/data aborts can occur, or the
user can observe abnormal program operation.
Any kind of reset logically remaps the Flash/EE memory to
the bottom of the memory array.
SYSMAP Register
Name:
SYSMAP
Address:
0xFFFF0220
Default Value: Updated by the kernel
Access:
Read/write
Function:
This 8-bit register allows user code to remap
either RAM or Flash/EE space into the bottom
of the ARM memory space starting at Address
0x00000000.
Table 7. SYSMAP MMR Bit Designations
Bit
Description
7 to 1
Reserved. These bits are reserved and should be written
as 0 by user code.
0
Remap bit.
This bit is set by the user to remap the SRAM to
0x00000000.
This bit is cleared automatically after reset to remap the
Flash/EE memory to 0x00000000.
RESET
There are four kinds of reset: external reset, power-on-reset,
watchdog reset, and software reset. The RSTSTA register
indicates the source of the last reset and can also be written
by user code to initiate a software reset event. The bits in this
register can be cleared to 0 by writing to the RSTCLR MMR at
0xFFFF0234. The bit designations in RSTCLR mirror those of
RSTSTA. These registers can be used during a reset exception
service routine to identify the source of the reset. The implica-
tions of all four kinds of reset event are tabulated in Table 9.
RSTSTA Register
Name:
RSTSTA
Address:
0xFFFF0230
Default Value: N/A
Access:
Read/write
Function:
This 8-bit register indicates the source of the
last reset event and can also be written by user
code to initiate a software reset.
RSTCLR Register
Name:
RSTCLR
Address:
0xFFFF0234
Access:
Write only
Function: This 8-bit write-only register clears the
corresponding bit in RSTSTA.
Table 8. RSTSTA/RSTCLR MMR Bit Designations
Bit
Description
7 to 4
Not used. These bits are not used and always read as 0.
3
External reset.
This bit is set by hardware when an external reset occurs.
This bit is cleared by setting the corresponding bit in RSTCLR.
2
Software reset.
This bit is set by user code to generate a software reset.
This bit is cleared by setting the corresponding bit in RSTCLR.1
1
Watchdog timeout.
This bit is set by hardware when a watchdog timeout occurs.
This bit is cleared by setting the corresponding bit in RSTCLR.
0
Power-on reset.
This bit is set by hardware when a power-on-reset occurs.
This bit is cleared by setting the corresponding bit in RSTCLR.
1
If the software reset bit in RSTSTA is set, any write to RSTCLR that does not
clear this bit generates a software reset.
Table 9. Device Reset Implications
Impact
RESET
Reset External
Pins to Default
State
Kernel
Executed
Reset All External
MMRs (Excluding
RSTSTA)
Reset All HV
Indirect
Registers
Peripherals
Reset
Watchdog
Timer Reset
RAM
Valid1
RSTSTA (Status
After Reset Event)
POR
Yes
Yes/No2
RSTSTA[0] = 1
Watchdog
Yes
No
Yes
RSTSTA[1] = 1
Software
Yes
No
Yes
RSTSTA[2] = 1
External Pin
Yes
No
Yes
RSTSTA[3] = 1
1
RAM is not valid in the case of a reset following LIN download.
2
The impact on RAM is dependent on the HVSTA[2] contents if LVF is enabled. When LVF is enabled using HVCFG[4], RAM has not been corrupted by the POR reset
mechanism if the LVF Status Bit HVSTA[2] is 1. See the Low Voltage Flag (LVF) section for more information.
相關PDF資料
PDF描述
EYM15DRSH CONN EDGECARD 30POS DIP .156 SLD
AIUR-06-102K INDUCTOR POWER 1000UH 10% T/H
V300C3V3C50B2 CONVERTER MOD DC/DC 3.3V 50W
EGM15DRSH CONN EDGECARD 30POS DIP .156 SLD
EVAL-ADUC7023QSPZ1 BOARD EVAL FOR ADUC7023
相關代理商/技術參數
參數描述
EVAL-ADUC7060QSPZ 功能描述:KIT DEV QUICK START ADUC7060 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
EVAL-ADUC7060QSPZU1 制造商:Analog Devices 功能描述:
EVALADUC7060QSPZU2 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Boxed Product (Development Kits)
EVAL-ADUC7061MKZ 功能描述:開發板和工具包 - ARM Quick Start Development System RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
EVAL-ADUC7061MKZ 制造商:Analog Devices 功能描述:ADUC7061MKZ EvaluationBoard
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*