參數資料
型號: EVAL-ADUC7039QSPZ
廠商: Analog Devices Inc
文件頁數: 38/92頁
文件大小: 0K
描述: BOARD EVAL FOR ADUC7039
設計資源: ADuC7039QSPZ Gerber Files
EVAL-ADuC7039 Schematic & Brd Outline
標準包裝: 1
系列: QuickStart™ PLUS 套件
類型: MCU
適用于相關產品: ADuC7039
所含物品:
Data Sheet
ADuC7039
Rev. D | Page 43 of 92
ADC SINC3 DIGITAL FILTER RESPONSE
The overall frequency response on all ADuC7039 ADCs is
dominated by the low-pass filter response of the on-chip sinc3
digital filters. The sinc3 filters are used to decimate the ADC
Σ-Δ modulator output data bit stream to generate a valid 16-bit
data result. The digital filter response is identical for both ADCs
and is configured via the 16-bit ADC filter (ADCFLT) register.
This register determines the overall throughput rate of the
ADCs. The noise resolution of the ADCs is determined by the
programmed ADC throughput rate. In the case of the current
channel ADC, the noise resolution is determined by throughput
rate and selected gain.
The overall frequency response and the ADC throughput is
dominated by the configuration of the sinc3 filter decimation
factor (SF) bits (ADCFLT[6:0]) and the averaging factor (AF)
bits (ADCFLT[13:8]). Due to limitations on the digital filter
internal data path, there are some limitations on the allowable
combinations of SF and AF that can be used to generate a
required ADC output rate. This restriction limits the minimum
ADC update in normal power mode to 10 Hz. The calculation
of the ADC throughput rate is detailed in the ADCFLT bit
designations table and the restrictions on allowable combi-
nations of AF and SF values are outlined in Table 33.
By default, the ADCFLT = 0x0007 configures the ADCs for a
throughput of 1.0 kHz with all other filtering options (chop,
running average, averaging factor, and sinc3 modify) disabled.
A typical filter response based on this default configuration is
Figure 14. Typical Digital Filter Response at fADC = 1.0 kHz
(ADCFLT = 0x0007)
An additional sinc3 modify bit (ADCFLT[7]) is also available in
the ADCFLT register. This bit is set by user code to modify the
standard sinc3 frequency response increasing the filter stop-
band rejection by approximately 5 dB. This is achieved by
inserting a second notch (NOTCH2) at
fNOTCH2 = 1.333 × fNOTCH
where fNOTCH is the location of the first notch in the response.
There is a slight increase in ADC noise if this bit is active.
Figure 15 shows the modified 1 kHz filter response when the
sinc3 modify bit is active. The new notch is clearly visible at
1.33 kHz, as is the improvement in stop-band rejection when
compared to the standard 1 kHz response.
Figure 15. Modified Sinc3 Digital Filter Response at fADC = 1.0 kHz
(ADCFLT = 0x0087)
At very low throughput rates, the chop bit in the ADCFLT
register can be enabled to minimize offset errors and, more
importantly, temperature drift in the ADC offset error.
There are two primary variables (sinc3 decimation factor
and averaging factor) available to allow the user to select an
optimum filter response, trading off filter bandwidth against
ADC noise.
For example, with the chop bit (ADCFLT[15]) set to 1,
increasing the SF value (ADCFLT[6:0]) to 0x1F (31
decimal) and selecting an AF value (ADCFLT[13:8]) of
0x16 (22 decimal) results in an ADC throughput of 10 Hz.
The frequency response in this case is shown in Figure 16.
Figure 16. Typical Digital Filter Response at fADC = 10 Hz, (ADCFLT = 0x961F)
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
500
1000 1500 2000 2500 3000 3500 4000 4500 5000
(d
B)
FREQUENCY (Hz)
08463-
015
(d
B)
FREQUENCY (kHz)
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
0.5
1.5
2.5
3.5
4.0
4.5
3.0
2.0
1.0
5.0
08463-
016
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
200
180
160
140
120
100
80
60
40
20
(d
B)
FREQUENCY (Hz)
08463-
017
相關PDF資料
PDF描述
EYM15DRSH CONN EDGECARD 30POS DIP .156 SLD
AIUR-06-102K INDUCTOR POWER 1000UH 10% T/H
V300C3V3C50B2 CONVERTER MOD DC/DC 3.3V 50W
EGM15DRSH CONN EDGECARD 30POS DIP .156 SLD
EVAL-ADUC7023QSPZ1 BOARD EVAL FOR ADUC7023
相關代理商/技術參數
參數描述
EVAL-ADUC7060QSPZ 功能描述:KIT DEV QUICK START ADUC7060 RoHS:是 類別:編程器,開發系統 >> 通用嵌入式開發板和套件(MCU、DSP、FPGA、CPLD等) 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板,軟件,4x4 鍵盤,光學撥輪,QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
EVAL-ADUC7060QSPZU1 制造商:Analog Devices 功能描述:
EVALADUC7060QSPZU2 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Boxed Product (Development Kits)
EVAL-ADUC7061MKZ 功能描述:開發板和工具包 - ARM Quick Start Development System RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
EVAL-ADUC7061MKZ 制造商:Analog Devices 功能描述:ADUC7061MKZ EvaluationBoard