- 您現在的位置：買賣IC網 > PDF目錄15530 > EVAL-ADUC7039QSPZ (Analog Devices Inc)BOARD EVAL FOR ADUC7039 PDF資料下載
參數資料
| 型號： | EVAL-ADUC7039QSPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 39/92頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADUC7039 |
| 設計資源： | ADuC7039QSPZ Gerber Files EVAL-ADuC7039 Schematic & Brd Outline |
| 標準包裝： | 1 |
| 系列： | QuickStart™ PLUS 套件 |
| 類型： | MCU |
| 適用于相關產品： | ADuC7039 |
| 所含物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
ADuC7039
Data Sheet
Rev. D | Page 44 of 92
In ADC low power mode, the ADC, Σ-Δ modulator clock is
no longer driven at 512 kHz but is driven directly from the
on-chip low power (128 kHz) oscillator. Subsequently, for the
same ADCFLT configurations in normal mode, all filter values
should be scaled by a factor of approximately four.
In general, it is possible to program different values of SF and
AF in the ADCFLT register and achieve the same ADC update
rate. In practical terms, the trade off with any value of ADCFLT
is frequency response vs. ADC noise. For optimum filter response
and ADC noise when using combinations of SF and AF, best
practice suggests choosing an SF in the range of 16 decimal to
40 decimal, or 0x10 to 0x28, and then increasing the AF value
to achieve the required ADC throughput. Table 35 shows some
common ADCFLT configurations.
ADC MODES OF OPERATION
The ADCs can be configured into reduced (low power) or
full power (normal) mode of operation by configuring
ADCMDE[3] as appropriate. The ARM7 MCU can also be
configured in low power modes of operation (POWCON[5:3]).
The core power modes are independently controlled and are
not related to the ADC power modes described in this section.
ADC Normal Power Mode
In normal mode, the current and voltage/temperature channels
are fully enabled. The ADC modulator clock is 512 kHz and
enables the ADCs to provide regular conversion results at a
rate of between 10 Hz and 1 kHz (see the ADC Filter Register
section). Both channels are under full control of the MCU and
can be reconfigured at any time. The default ADC update rate
for all channels in this mode is 1.0 kHz.
It is worth emphasizing that I-ADC and V/T-ADC channels can
be configured to initiate periodic, normal power mode, high
accuracy, single conversion cycles before returning to ADC full
power-down mode. This flexibility is facilitated under full MCU
control via the ADCMDE MMR; it ensures that continuous peri-
odic monitoring of battery current, voltage, and temperature
settings is feasible while ensuring the average dc current
consumption is minimized.
In ADC normal mode, the PLL must not be powered down.
ADC Low Power Mode
In ADC low power mode, the I-ADC is enabled in a reduced
power and reduced accuracy configuration. The ADC modu-
lator clock is now driven directly from the on-chip 128 kHz low
power oscillator. The gain of the ADC in this mode is fixed at 512.
All of the ADC peripheral functions (result counter, digital
comparator and accumulator) can be enabled in low power mode.
Typically, in low power mode, the I-ADC only, is configured
to run at a low update rate, continuously monitoring battery
current. The MCU is in power-down mode and wakes up when
the I-ADC interrupts the MCU. This happens after the I-ADC
detects a current conversion beyond a preprogrammed thre-
shold, setpoint, or a set number of conversions.
ADC Comparator and Accumulator
Every I-ADC result can also be compared to a preset threshold
level (ADC0TH) as configured via ADCCFG[3]. An MCU
interrupt is generated if the absolute (sign independent) value
of the ADC result is greater than the preprogrammed com-
parator threshold level.
Finally, a 32-bit accumulator (ADC0ACC) function can be
configured (ADCCFG[5]) allowing the I-ADC to add (or
subtract) multiple I-ADC sample results. User code can read
the accumulated value directly (ADC0ACC) without any
further software processing.
ADC Continuous Interrupt Mode
Setting ADCMDE[5] allows the user to generate an ADC
interrupt after each ADC conversion period, even if the ADC
filter is not fully settled. The corresponding ADC interrupt bit
in the ADCMSKI must also be set to allow the continuous
interrupt. In this mode of operation, ADCSTA[2:0] are used
as valid flags and should not be used to generate interrupts.
Table 35. Common ADCFLT Configurations
ADC Mode
SF
AF
Other Config.
ADCFLT
fADC
tSETTLE
Normal
0x1F
0x16
Chop on
0x961F
10 Hz
0.2 sec
Normal
0x07
0x00
None
0x0007
1 kHz
3 ms
Normal
0x07
0x00
Sinc3 modify
0x0087
1 kHz
3 ms
Low Power
0x10
0x03
Chop on
0x8310
20 Hz
100 ms
Low Power
0x10
0x09
Chop on
0x8910
10 Hz
200 ms
相關PDF資料 |
PDF描述 |
|---|---|
| EYM15DRSH | CONN EDGECARD 30POS DIP .156 SLD |
| AIUR-06-102K | INDUCTOR POWER 1000UH 10% T/H |
| V300C3V3C50B2 | CONVERTER MOD DC/DC 3.3V 50W |
| EGM15DRSH | CONN EDGECARD 30POS DIP .156 SLD |
| EVAL-ADUC7023QSPZ1 | BOARD EVAL FOR ADUC7023 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADUC7060QSPZ | 功能描述:KIT DEV QUICK START ADUC7060 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA |
| EVAL-ADUC7060QSPZU1 | 制造商:Analog Devices 功能描述: |
| EVALADUC7060QSPZU2 | 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Boxed Product (Development Kits) |
| EVAL-ADUC7061MKZ | 功能描述:開發板和工具包 - ARM Quick Start Development System RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| EVAL-ADUC7061MKZ | 制造商:Analog Devices 功能描述:ADUC7061MKZ EvaluationBoard |
發布緊急采購，3分鐘左右您將得到回復。