參數資料
型號： EVAL-ADUC7039QSPZ
廠商： Analog Devices Inc
文件頁數： 74/92頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR ADUC7039
設計資源： ADuC7039QSPZ Gerber Files
EVAL-ADuC7039 Schematic & Brd Outline
標準包裝： 1
系列： QuickStart™ PLUS 套件
類型： MCU
適用于相關產品： ADuC7039
所含物品： 板
ADuC7039
Data Sheet
Rev. D | Page 76 of 92
SPI Control Register
Name:
SPICON
Address:
0xFFFF0A10
Default Value:
0x0000
Access:
Read/write
Function:
This 16-bit MMR configures the SPI peripheral in both master and slave modes.
Table 55. SPICON MMR Bit Designations
Bit
Description
15 to 14
SPI IRQ mode bits. These bits configure when the Tx/Rx interrupts occur in a transfer.
00 = Tx interrupt occurs when 1 byte has been transferred. Rx interrupt occurs when 1 or more bytes have been received into the FIFO.
01 = Tx interrupt occurs when 2 bytes have been transferred. Rx interrupt occurs when 1 or more bytes have been received into
the FIFO.
10 = Tx interrupt occurs when 3 bytes have been transferred. Rx interrupt occurs when 3 or more bytes have been received into
the FIFO.
11 = Tx interrupt occurs when 4 bytes have been transferred. Rx interrupt occurs when the Rx FIFO is full, or 4 bytes are present.
13
SPI Tx FIFO flush enable bit.
Set this bit to flush the Tx FIFO. This bit does not clear itself and should be toggled if a single flush is required. If this bit is left high, then
either the last transmitted value or 0x00 is transmitted depending on SPICON[7]. Any writes to the Tx FIFO are ignored while this
bit is set.
Clear this bit to disable Tx FIFO flushing.
12
SPI Rx FIFO flush enable bit.
Set this bit to flush the Rx FIFO. This bit does not clear itself and should be toggled if a single flush is required. If this bit is set,
all incoming data is ignored and no interrupts are generated. If set and SPICON[6] = 0, a read of the Rx FIFO initiates a transfer.
Clear this bit to disable Rx FIFO flushing.
11
Continuous transfer enable.
This bit is set by the user to enable continuous transfer. In master mode, the transfer continues until no valid data is available in
the SPITX register. SS is asserted and remains asserted for the duration of each 8-bit serial transfer until TX is empty.
This bit is cleared by the user to disable continuous transfer. Each transfer consists of a single 8-bit serial transfer. If valid data
exists in the SPITX register, then a new transfer is initiated after a stall period of 1 serial clock cycle.
10
Loop back enable bit.
This bit is set by the user to connect MISO to MOSI and test software.
This bit is cleared by the user to be in normal mode.
9
Slave MISO output enable bit.
Set this bit to disable the output driver on the MISO pin. The MISO pin becomes open drain when this bit is set.
Clear this bit for MISO to operate as normal.
8
SPIRX overflow overwrite enable.
This bit is set by the user; the valid data in the SPIRX register is overwritten by the new serial byte received.
This bit is cleared by the user; the new serial byte received is discarded.
7
SPI transmit zeros when Tx FIFO enable bit.
Set this bit to transmit 0x00 when there is no valid data in the Tx FIFO.
Clear this bit to transmit the last transmitted value when there is no valid data in the Tx FIFO.
6
SPI transfer and interrupt mode.
This bit is set by the user to initiate a transfer with a write to the SPITX register. Interrupt only occurs when SPITX is empty.
This bit is cleared by the user to initiate a transfer with a read of the SPIRX register. Interrupt only occurs when SPIRX is full.
5
LSB first transfer enable bit.
This bit is set by the user; the LSB is transmitted first.
This bit is cleared by the user; the MSB is transmitted first.
相關PDF資料
PDF描述
EYM15DRSH CONN EDGECARD 30POS DIP .156 SLD
AIUR-06-102K INDUCTOR POWER 1000UH 10% T/H
V300C3V3C50B2 CONVERTER MOD DC/DC 3.3V 50W
EGM15DRSH CONN EDGECARD 30POS DIP .156 SLD
EVAL-ADUC7023QSPZ1 BOARD EVAL FOR ADUC7023
相關代理商/技術參數
參數描述
EVAL-ADUC7060QSPZ 功能描述:KIT DEV QUICK START ADUC7060 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
EVAL-ADUC7060QSPZU1 制造商:Analog Devices 功能描述:
EVALADUC7060QSPZU2 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Boxed Product (Development Kits)
EVAL-ADUC7061MKZ 功能描述:開發板和工具包 - ARM Quick Start Development System RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
EVAL-ADUC7061MKZ 制造商:Analog Devices 功能描述:ADUC7061MKZ EvaluationBoard
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*