參數資料
型號: OMAP5910(RISC)
英文描述: Dual-Core Processor
中文描述: 雙核處理器
文件頁數: 62/160頁
文件大小: 1997K
代理商: OMAP5910(RISC)
Functional Overview
50
August 2002 Revised August 2003
SPRS197B
The main features of the UART peripherals include:
Selectable UART/autobaud modes (autobauding on UART1 and UART2)
Dual 64-entry FIFOs for received and transmitted data payload
Programmable and selectable transmit and receive FIFO trigger levels for DMA and interrupt generation
Programmable sleep mode
Complete status-reporting capabilities in both normal and sleep mode
Frequency prescaler values from 0 to 65535 to generate the appropriate baud rates
Interrupt request generated if multiple System DMA requests
Baud rate from 300 bits/s up to 1.5M bits/s
Autobauding between 1200 bits/s and 115.2K bits/s
Software/hardware flow control
Programmable XON/XOFF characters
Programmable auto-RTS and auto-CTS
Programmable serial interface characteristics
5-, 6-, 7-, or 8-bit characters
Even-, odd-, or no-parity bit generation and detection
1, 1.5, or 2 stop-bit generation
False start bit detection
Line break generation and detection
Fully prioritized interrupt system controls
Internal test and loopback capabilities
Modem control functions (CTS, RTS, DSR, DTR)
NOTE:
DSR and DTR are only available on UART1 and UART3.
The IrDA functions available on UART3 are as follows:
Slow infrared (SIR) operations
Framing error, cyclic redundancy check (CRC) error, abort pattern (SIR) detection
8-entry status FIFO (with selectable trigger levels) available to monitor frame length and frame errors
3.8.2 General-Purpose I/O (GPIO)
There are up to 14 shared GPIO pins on the OMAP5910 device which may be accessed and controlled by
either the DSP public peripheral bus or the MPU public peripheral bus. Each GPIO pin is independently
configurable to be used by either the DSP or MPU. The MPU controls which processor owns each GPIO pin
by configuring a pin control register that only the MPU can access.
Each GPIO pin can be used as either an input or output pin with GPIO inputs being synchronized internally
to a peripheral clock. GPIO inputs may also optionally be configured to generate an interrupt condition to the
processor which owns the GPIO pin. The sense of the interrupt condition is configurable such that either a
high-to-low or low-to-high transition causes the interrupt condition.
Some of the GPIO pins are multiplexed with other interface pins specific to other device peripherals. Refer
to Table 23 to decide which GPIO pins are multiplexed with other peripheral signals.
3.8.3 Mailbox Registers
Four sets of shared mailbox registers are available for communication between the DSP and MPU. These
registers are discussed further in Section 3.12, Interprocessor Communication.
相關PDF資料
PDF描述
OMC506 Closed Loop Speed Controller For 3-Phase Brushless DC Motor MP-3T Package
OMC507 5 Amp. Push-Pull 3-Phase Brushless DC Motor Controller Driver(5A,推挽三相無刷直流電機控制驅動器)
OMC510 36V Hi-Rel Three-Phase Brushless DC Motor Controller in a PCB-1 package
OMC510 DSP-Based Three-Phase Brushless DC Motor Controller(基于DSP的三相無刷直流電機控制器)
OMD100F60HL TRANSISTOR | IGBT POWER MODULE | HALF BRIDGE | 600V V(BR)CES | 150A I(C)
相關代理商/技術參數
參數描述
OMAP5912 制造商:TI 制造商全稱:Texas Instruments 功能描述:Applications Processor
OMAP5912GDYAR 制造商:Texas Instruments 功能描述:- Tape and Reel
OMAP5912ZDY 功能描述:處理器 - 專門應用 Applications Processor RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
OMAP5912ZDYA 制造商:Texas Instruments 功能描述:APPLICATIONS PROCESSOR - Trays
OMAP5912ZZG 功能描述:處理器 - 專門應用 Applications Processor RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432