參數資料
型號： M37640E8
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCONTROLLER
中文描述： 單芯片8位CMOS單片機
文件頁數： 16/172頁
文件大?。?/td> 1193K
代理商： M37640E8
2-4
7/9/98
Central Processing Unit
7600 Series
M37640E8-XXXF Preliminary Specification
Mitsubishi Microcomputers
2.1.3
Index Registers X and Y
Both index registers X and Y are 8-bit registers. In the absolute addressing modes, the contents of
these registers are added to the value of the OPERAND to specify the real address.
In the indirect X addressing mode, the value of the OPERAND is added to the contents of register X
to specify the zero page basic address. The data at the basic address specifies the real address.
In the indirect Y addressing mode, the value of the operand specifies a zero page address. The data at
this address is added to the contents of register Y to produce the real address. These addressing modes
are useful for referencing subroutine tables and memory tables.
When the T flag in the processor status register is set high, the value contained in index register X points
to a zero page memory location that replaces the accumulator for most accumulator based instructions.
2.1.4
Stack Pointer
The stack pointer is an 8-bit register used during subroutine calls and interrupts. The stack is used to
store the current address data and processor status when branching to subroutines or interrupt routines.
The lower eight bits of the stack address are determined by the contents of the stack pointer. The
upper eight bits of the stack address are determined by the Stack Page Select Bit, bit 2 of the CPU
Mode Register A. If the Stack Page Select bit is “0”, then the RAM in the zero page (addresses
0070
16
to 00FF
16
) is used as the stack area. If the stack page select bit is “1” (the default value), then
the RAM in one page (addresses 0100
16
to 01FF
16
) is used as the stack area. The base of the stack
must be set in software, and stack grows towards lower addresses from that point. The operations of
pushing register contents onto the stack and popping them from the stack are shown in Figure 2-2.
2.1.5
Program Counter
The program counter (PC) is a 16-bit register consisting of two 8-bit sub-registers PCH and PCL. It is
used to indicate the address of the next instruction to be executed.
相關PDF資料
PDF描述
M37641F8-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641M8-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641M8 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M37640E8FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640E8FS 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
M37640M4T 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-111FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-126FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*