參數資料
型號: M37640E8
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCONTROLLER
中文描述: 單芯片8位CMOS單片機
文件頁數: 109/172頁
文件大?。?/td> 1193K
代理商: M37640E8
7600 Series
Mitsubishi Microcomputer
M37640E8-XXXF Preliminary Specification
UART
7/9/98
2-97
When the last bit is transmitted, the TCM flag is set to a “1” if the transmit buffer is empty,
TEN is a “0”, or CTS handshaking is enabled and CTSx is “1”. If the transmit buffer is not
empty, TEN is a “1”, and CTS handshaking is disabled or CTS handshaking is enabled and CTSx
is low, the TCM flag is not set because transfer of the contents of the transmit buffer to the
transmit shift register occurs immediately.
Figure 2-112. UART Transmit Operation Waveforms
Receive Method
(See Figure 2-113.)
Set up
Define the baud rate by writing a value from 0-255 into UxBRG.
Set the Receive Initialization Bit (RIN, bit 3 in the UxCON), to “1”.
Configure the data format and the clock selection by writing the appropriate value to UxMOD.
Set the Request-To-Send Enable Bit (RTS_SEL, bit 6 of UxCON), if RTS handshaking will be
used.
Set the Receive Enable Bit (REN, bit 1 in the UxCON), to “1”.
Operation
When a falling edge is detected on the URXDx pin, the value on the pin is sampled at the basic
clock rate, which is 16 times faster than the baud rate. If the pin is low for at least two cycles
of the basic clock, the start bit is detected. Sampling is again performed three times in the
approximate middle of the start bit. If two or more of the samples are low, the start bit is
deemed valid. If two or more of the samples are not low, the start bit is invalidated and the
UART again begins waiting for a falling edge on the URXDx pin.
Once a valid start bit has been detected, input data received through the URXDx pin is read one
bit at a time, LSB first, into the receive shift register. As is the case with the start bit, three
samples are taken in the approximate middle of each data bit, the parity bit, and the stop bit(s).
If two or more of the samples are low, a “0” is latched, and if two or more of the samples are
high, a “1” is latched.
When the number of bits specified by the data format has been received and the last stop bit is
UxTRB1
Write
UxBRG
Clock
UTXDx
TBE
Start bit
D0
Stop bit
Start bit
Stop bit
TCM
相關PDF資料
PDF描述
M37641F8-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641M8-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641M8 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M37640E8FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640E8FS 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 類別:編程器,開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230,RCB231,RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
M37640M4T 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-111FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-126FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER