- 您現在的位置：買賣IC網 > PDF目錄379876 > celeron 700 (Intel Corp.) Intel Celeron Processor Up To 700 MHz(頻率達700MHz的INTEL Celeron 處理器) PDF資料下載
參數資料
| 型號： | celeron 700 |
| 廠商： | Intel Corp. |
| 英文描述： | Intel Celeron Processor Up To 700 MHz(頻率達700MHz的INTEL Celeron 處理器) |
| 中文描述： | 英特爾賽揚處理器高達700兆赫（頻率達700MHz的英特爾賽揚處理器的） |
| 文件頁數： | 19/118頁 |
| 文件大?。?/td> | 990K |
| 代理商： | CELERON 700 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁
Datasheet
19
Intel
Celeron Processor up to 700 MHz
2.6
System Bus Unused Pins
All RESERVED pins must remain unconnected. Connection of these pins to V
CCCORE
, V
SS
, or to
any other signal (including each other) can result in component malfunction or incompatibility
with future Intel
Celeron processor products. See
Section 5.0
for a pin listing of the processor
and the location of each RESERVED pin.
For Intel Celeron processors in the S.E.P. Package, the TESTHI pin must be at a logic-high level
when the core power supply comes up. For more information, please refer to erratum C26 of the
Intel
Celeron Processor Specification Update
(Order Number 243748). Also note that the
TESTHI signal is not available on Intel Celeron processors in the PGA package.
PICCLK must be driven with a valid clock input and the PICD[1:0] lines must be pulled-up to
2.5 V even when the APIC will not be used. A separate pull-up resistor must be provided for each
PICD line.
For reliable operation, always connect unused inputs or bi-directional signals to their deasserted
signal level. The pull-up or pull-down resistor value is system dependent and should be chosen
such that the logic-high (V
IH
) and logic-low (V
IL
) requirements are met.
For the S.E.P. Package, unused AGTL+ inputs should not be connected as the package substrate
has termination resistors. On the other hand, the PGA packages do not have AGTL+ termination in
their package and must have any unused AGTL+ inputs terminated through a pull-up resistor. For
designs that intend to only support the FC-PGA processor, unused AGTL+ inputs will be
terminated by the processor’s on-die termination resistors and, thus, do not need to be terminated
on the motherboard. However, the reset pin should always be terminated on the motherboard.
For unused CMOS inputs, active-low signals should be connected through a pull-up resistor to
meet V
IH
requirements and active-high signals should be connected through a pull-down resistor to
meet V
IL
requirements. Unused CMOS outputs can be left unconnected. A resistor must be used
when tying bi-directional signals to power or ground. For any signal pulled to either power or
ground, a resistor will allow for system testability.
2.7
Processor System Bus Signal Groups
To simplify the following discussion, the Intel
Celeron processor system bus signals have been
combined into groups by buffer type.
All Intel
Celeron processor system bus outputs are
open drain
and require a high-level source provided externally by the termination or pull-up
resistor.
AGTL+ input signals have differential input buffers, which use V
REF
as a reference signal. AGTL+
output signals require termination to 1.5 V. In this document, the term "AGTL+ Input" refers to the
AGTL+ input group as well as the AGTL+ I/O group when receiving. Similarly, "AGTL+ Output"
refers to the AGTL+ output group as well as the AGTL+ I/O group when driving.
EMI pins (S.E.P. Package only) should be connected to motherboard ground and/or to chassis
ground through zero ohm (0
) resistors. The zero ohm resistors should be placed in close
proximity to the SC242 connector. The path to chassis ground should be short in length and have a
low impedance.
The PWRGOOD, BCLK, and PICCLK inputs can each be driven from ground to 2.5 V. Other
CMOS inputs (A20M#, IGNNE#, INIT#, LINT0/INTR, LINT1/NMI, PREQ#, SMI, SLP#, and
STPCLK#) must be pulled up to V
CCCMOS
. In addition, the CMOS, APIC, and TAP outputs are
相關PDF資料 |
PDF描述 |
|---|---|
| celeron cpu Mobile Module | processor Mobile Module Connector 1 (MMC-1) at 466 MHz and 433MHZ(工作頻率466和433兆赫茲帶連接器1處理器) |
| celeron CPU with Mobile Module | processor Mobile Module Connector 2 (MMC-2) at 466 MHz and 433MHZ(工作頻率466和433兆赫茲帶連接器2處理器) |
| Celeron Processor with mobile | Celeron Processor Mobile Module MMC-1 at 400 MHz, 366 MHz, 333 MHz, and 300 MHz(工作頻率400,366,333,300和266兆赫茲帶移動模塊和連接器1處理器) |
| celeron processor | 32 bit Celeron Processor Mobile Module(32 位帶移動模塊處理器) |
| CEM11C2 | Dual Enhancement Mode Field Effect Transistor (N and P Channel) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CELF001001J1 | 制造商:Panasonic Industrial Company 功能描述:FILTER |
| CELHK11-1REC5-59-3.00-AV-01-V | 功能描述:CIRCUIT BRKR MAG-HYDR LEVER 3A 制造商:sensata technologies/airpax 系列:CEL 零件狀態:有效 斷路器類型:磁性（液力延遲） 額定電流:3A 額定電壓 - AC:- 額定電壓 - DC:- 極數:2 致動器類型:搖臂 照明:- 照明電壓（標稱值）:- 安裝類型:面板安裝 標準包裝:1 |
| CELHK11-1REC5-59-35.0-AV-01-V | 功能描述:CIRCUIT BRKR MAG-HYDR LEVER 35A 制造商:sensata technologies/airpax 系列:CEL 零件狀態:有效 斷路器類型:磁性（液力延遲） 額定電流:35A 額定電壓 - AC:- 額定電壓 - DC:- 極數:2 致動器類型:搖臂 照明:- 照明電壓（標稱值）:- 安裝類型:面板安裝 標準包裝:1 |
| CELHK11-1REC5-71165-10-V | 功能描述:CIRCUIT BREAKER MAG-HYDR LEVER 制造商:sensata technologies/airpax 系列:* 零件狀態:有效 標準包裝:1 |
| CELHK11-1REC5-71165-11-V | 功能描述:CIRCUIT BREAKER MAG-HYDR LEVER 制造商:sensata technologies/airpax 系列:* 零件狀態:有效 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。