參數資料
型號： S1C88848D0A0100
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC192
封裝： DIE-192
文件頁數： 35/174頁
文件大?。?/td> 1304K
代理商： S1C88848D0A0100
S1C88848 TECHNICAL MANUAL
EPSON
5
1 INTRODUCTION
1.4 Mask Option
Mask options shown below are provided for the
S1C88848. Several hardware specifications are
prepared in each mask option, and one of them can
be selected according to the application. The
function option generator winfog, that has been
prepared as the development software tool of the
S1C88848, is used for this selection. Mask pattern
of the IC is finally generated based on the data
created by the winfog. Refer to the "S5U1C88000C
Manual II" for details on the winfog.
S1C88848 optional specifications
(1)
___________
RESET terminal pull-up resistor
This mask option can select whether the pull-up
___________
resistor for the RESET terminal is used or not.
(2) External reset by simultaneous LOW
input to the input port (K00–K03)
This function resets the IC when several keys
are pressed simultaneously. The mask option is
used to select whether this function is used or
not. Further when the function is used, a
combination of the input ports (K00–K03),
which are connected to the keys to be pressed
simultaneously, can be selected. Refer to Section
4.1.2, "Simultaneous LOW level input at input
port terminals K00–K03", for details.
(3) OSC1 oscillation circuit
The specification of the OSC1 oscillation circuit
can be selected from "Crystal oscillation" and
"CR oscillation". Refer to Section 5.3.3, "OSC1
oscillation circuit", for details.
(4) OSC3 oscillation circuit
The specification of the OSC3 oscillation circuit
can be selected from among three types:
"Crystal oscillation", "Ceramic oscillation" and
"CR oscillation". Refer to Section 5.3.4, "OSC3
oscillation circuit", for details.
(5) Input port pull-up resistor
This mask option can select whether the pull-up
resistor for the input port terminal is used or
not. It is possible to select for each bit of the
input ports. Refer to Section 5.4, "Input Ports (K
ports)", for details.
(6) R26, R51 output port specifications
The R26 port can be configured as a general-
_________
purpose output port, TOUT output port (TOUT
inverted output) or REM (remoto-control
carrier) output port.
The R51 port can be configured as a general-
_____
purpose output port or BZ output port (BZ
inverted output). Refer to Section 5.5, "Output
Ports (R ports)", for details.
(7) I/O port pull-up resistor
This mask option can select whether the pull-up
resistor for the I/O port terminal (it works
during input mode) is used or not. It is possible
to select for each bit of the I/O ports. Refer to
Section 5.6, "I/O Ports (P ports)", for details.
Since P10 to P13 are shared with the serial
interface I/O terminals, the selected P10 and
P12 terminal configuration is applied to the
serial input (SIN) terminal and serial clock input
_________
terminal (SCLK in clock synchronous mode)
when the serial interface is used. Refer to
Section 5.7, "Serial Interface", for details.
(8) LCD drive duty
The drive duty for the built-in LCD driver can
be selected from software switchable (between
1/32 and 1/16), fixed at 1/17 and fixed at 1/8.
Refer to Section 5.11, "LCD Controller", for
details.
(9) LCD power supply
Either the internal power supply or an external
power supply can be selected as the LCD
system power source. Furthermore, when using
the internal power supply, the LCD drive
voltage can be set for a 4.5 V panel or a 5.5 V
panel and the drive bias to 1/5 or 1/4. Refer to
Section 5.11, "LCD Controller", for details.
(10) SEG40–SEG50 port specifications
The SEG40 to SEG50 ports can be configured as
LCD segment output ports or general-purpose
output ports. Refer to Section 5.11, "LCD
Controller", for details of the LCD segment
output, and Section 5.5, "Output Ports (R
ports)", for details of the DC output.
相關PDF資料
PDF描述
S1C8F360F 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP176
S1D13305F00B 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13305F00A 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13600F00A CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64
S1D13700F02A100 320 X 240 PIXELS CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64
相關代理商/技術參數
參數描述
S1C8F360D411000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360D511000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F413100 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F513200 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F626 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*