參數資料
型號： S1C88848D0A0100
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC192
封裝： DIE-192
文件頁數： 119/174頁
文件大?。?/td> 1304K
代理商： S1C88848D0A0100
S1C88848 TECHNICAL MANUAL
EPSON
41
5 PERIPHERAL CIRCUITS AND THEIR OPERATIO (Output Ports)
BZON: 00FF44HD0
_____
Controls the buzzer (BZ and BZ) signal output.
When "1" is written: Buzzer signal output ON
When "0" is written: Buzzer signal output OFF
Reading:
Valid
BZON is the output control register for buzzer
_____
signal. When "1" is set to the register, the BZ (BZ)
signal is output from the output port terminal R50
(R51). When "0" is set, the R50 goes LOW (VSS) and
the R51 goes HIGH (VDD).
To output the BZ signal, "0" must always be set for
the data register R50D. The data register R51D does
_____
not affect the BZ output.
At initial reset, BZON is set to "0" (output OFF).
_____
The BZ signal can be output from R51 only when
the function is selected by mask option.
BZSHT: 00FF44HD5
Controls the one-shot buzzer output.
When "1" is written: Trigger
When "0" is written: No operation
When "1" is read:
Busy
When "0" is read:
Ready
Writing "1" into BZSHT causes the one-shot output
_____
circuit to operate. The BZ (BZ) signal is output from
the R50 (R51) terminal. The buzzer output is
automatically turned OFF after the time set by
SHTPW has elapsed.
To output the BZ signal, "0" must always be set for
the data register R50D. The data register R51D does
_____
not affect the BZ output.
The one-shot output is only valid when the normal
buzzer output is OFF (BZON = "0") state. The
trigger is invalid during ON (BZON = "1") state.
When a re-trigger is assigned during a one-shot
output, the one-shot output time set with SHTPW is
measured again from that point. (time extension)
The operation status of the one-shot output circuit
can be confirmed by reading BZSHT, when the one-
shot output is ON, "1" is read from BZSHTand
when the output is OFF, "0" is read.
At initial reset, BZSHT is set to "0" (ready).
_____
The BZ signal can be output from R51 only when
the function is selected by mask option.
BZSTP: 00FF44HD6
Forcibly stops the one-shot buzzer output.
When "1" is written: Forcibly stop
When "0" is written: No operation
Reading:
Constantly "0"
By writing "1" into BZSTP, the one-shot buzzer
output can be stopped prior to the elapsing of the
time set with SHTPW.
Writing "0" is invalid and writing "1" except during
one-shot output is also invalid.
When "1" is written to BZSHT and BZSTP simulta-
neously, BZSTP takes precedence and one-shot
output becomes stop status.
Since BZSTP is for writing only, during readout it is
constantly set to "0".
5.5.7 Programming notes
(1)
_________
Since the special output signals (TOUT/TOUT,
_____
FOUT, BZ/BZ) are generated asynchronously
from the output control registers (PTOUT,
FOUTON, BZON, BZSHT and BZSTP), when
the signals is turned ON or OFF by the output
control register settings, a hazard of a 1/2 cycle
or less is generated.
(2) The SLP instruction has executed when the
_________
special output signals (TOUT/TOUT, FOUT,
_____
BZ/BZ) are in the enable status, an unstable
clock is output for the special output at the time
of return from the SLEEP state. Consequently,
when shifting to the SLEEP state, you should set
the special output signal to the disable status
prior to executing the SLP instruction.
(3) When the FOUT frequency is made "fOSC3/n",
you must turn on the OSC3 oscillation circuit
before outputting FOUT. A time interval of
several 100 sec to several 10 msec, from the
turning ON of the OSC3 oscillation circuit to
until the oscillation stabilizes, is necessary, due
to the oscillation element that is used. Conse-
quently, if an abnormality occurs as the result of
an unstable FOUT signal being output exter-
nally, you should allow an adequate waiting
time after turning ON of the OSC3 oscillation,
before turning outputting FOUT. (The oscilla-
tion start time will vary somewhat depending
on the oscillator and on the externally attached
parts. Refer to the oscillation start time example
indicated in Chapter 7, "ELECTRICAL CHAR-
ACTERISTICS".)
At initial reset, OSC3 oscillation circuit is set to
ON state.
相關PDF資料
PDF描述
S1C8F360F 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP176
S1D13305F00B 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13305F00A 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13600F00A CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64
S1D13700F02A100 320 X 240 PIXELS CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64
相關代理商/技術參數
參數描述
S1C8F360D411000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360D511000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F413100 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F513200 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F626 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*