參數資料
型號： S1C88848D0A0100
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC192
封裝： DIE-192
文件頁數： 147/174頁
文件大?。?/td> 1304K
代理商： S1C88848D0A0100
66
EPSON
S1C88848 TECHNICAL MANUAL
5 PERIPHERAL CIRCUITS AND THEIR OPERATION (Clock Timer)
TMD0–TMD7: 00FF41H
The clock timer data can be read out.
Each bit of TMD0–TMD7 and frequency corre-
spondence are as follows:
TMD0: 128Hz
TMD4: 8Hz
TMD1: 64Hz
TMD5: 4Hz
TMD2: 32Hz
TMD6: 2Hz
TMD3: 16Hz
TMD7: 1Hz
Since the TMD0–TMD7 is exclusively for reading,
the write operation is invalid.
At initial reset, the timer data is set to "00H".
TMRST: 00FF40HD1
Resets the clock timer.
When "1" is written: Clock timer reset
When "0" is written: No operation
Reading:
Always "0"
The clock timer is reset by writing "1" to the
TMRST.
When the clock timer is reset in the RUN status, it
restarts immediately after resetting. In the case of
the STOP status, the reset data "00H" is maintained.
No operation results when "0" is written to the
TMRST.
Since the TMRST is exclusively for writing, it
always becomes "0" during reading.
TMRUN: 00FF40HD0
Controls RUN/STOP of the clock timer.
When "1" is written: RUN
When "0" is written: STOP
Reading:
Valid
The clock timer starts up-counting by writing "1" to
the TMRUN and stops by writing "0".
In the STOP status, the count data is maintained
until it is reset or set in the next RUN status. Also,
when the STOP status changes to the RUN status,
the data that was maintained can be used for
resuming the count.
At initial reset, the TMRUN is set to "0" (STOP).
PTM0, PTM1: 00FF20HD0, D1
Sets the priority level of the clock timer interrupt.
The two bits PTM0 and PTM1 are the interrupt
priority register corresponding to the clock timer
interrupt. Table 5.8.3.2 shows the interrupt priority
level which can be set by this register.
Table 5.8.3.2 Interrupt priority level settings
At initial reset, this register is set to "0" (level 0).
ETM1, ETM2, ETM8, ETM32: 00FF22HD0–D3
Enables or disables the generation of an interrupt
for the CPU.
When "1" is written: Interrupt enabled
When "0" is written: Interrupt disabled
Reading:
Valid
The ETM1, ETM2, ETM8 and ETM32 are interrupt
enable registers that respectively correspond to the
interrupt factors for 1 Hz, 2 Hz, 8 Hz and 32 Hz.
Interrupts set to "1" are enabled and interrupts set
to "0" are disabled.
At initial reset, this register is set to "0" (interrupt
disabled).
FTM1, FTM2, FTM8, FTM32: 00FF24HD0–D3
Indicates the clock timer interrupt generation status.
When "1" is read:
Interrupt factor present
When "0" is read:
Interrupt factor not present
When "1" is written: Resets factor flag
When "0" is written: Invalid
The FTM1, FTM2, FTM8 and FTM32 are interrupt
factor flags that respectively correspond to the
interrupts for 1 Hz, 2 Hz, 8 Hz and 32 Hz and are
set to "1" at the falling edge of each signal.
When set in this manner, if the corresponding
interrupt enable register is set to "1" and the
corresponding interrupt priority register is set to a
higher level than the setting of interrupt flags (I0
and I1), an interrupt will be generated to the CPU.
Regardless of the interrupt enable register and
interrupt priority register settings, the interrupt
factor flag will be set to "1" by the occurrence of an
interrupt generation condition.
To accept the subsequent interrupt after interrupt
generation, re-setting of the interrupt flags (set
interrupt flag to lower level than the level indicated
by the interrupt priority registers, or execute the
RETE instruction) and interrupt factor flag reset are
necessary. The interrupt factor flag is reset to "0" by
writing "1".
At initial reset, this flag is reset to "0".
PTM1
PTM0
Interrupt priority level
1
0
1
0
1
0
Level 3 (IRQ3)
Level 2 (IRQ2)
Level 1 (IRQ1)
Level 0 (None)
相關PDF資料
PDF描述
S1C8F360F 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP176
S1D13305F00B 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13305F00A 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13600F00A CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64
S1D13700F02A100 320 X 240 PIXELS CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64
相關代理商/技術參數
參數描述
S1C8F360D411000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360D511000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F413100 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F513200 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F626 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*