- 您現在的位置：買賣IC網 > PDF目錄383255 > L9805 (意法半導體) Super Smart Power Motor Driver with 8-BIT MCU, CAN Interface, 16K EPROM, 256Bytes RAM, 128 Bytes EEPROM, 10 Bit ADC, WDG, 2 Timers, 2 PWM Modules, Ful PDF資料下載
參數資料
| 型號： | L9805 |
| 廠商： | 意法半導體 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Super Smart Power Motor Driver with 8-BIT MCU, CAN Interface, 16K EPROM, 256Bytes RAM, 128 Bytes EEPROM, 10 Bit ADC, WDG, 2 Timers, 2 PWM Modules, Ful |
| 中文描述： | 超級智能型電動馬達驅動器，帶有8位微控制器，CAN接口，16K的存儲器，256Bytes RAM內存，128字節EEPROM，10位ADC，水分散粒劑，2定時器，2個PWM模塊，涪陵 |
| 文件頁數： | 57/103頁 |
| 文件大?。?/td> | 853K |
| 代理商： | L9805 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁
57/103
L9805
5.5.3 Input Selections and Sampling
The input section of the ADC includes the analog
multiplexer and a buffer. The input of the buffer is
permanently connected to the multiplexer output.
The buffer output is fed to the sample and hold cir-
cuit.
The multiplexer is driven with CH1 and CH0 bit
only after ADST is set. Starting from this event, the
sampler follows the selected input signal for 2.5us
and then holds it for the remaining conversion time
(i.e. when the conversion is actually running).
5.5.4 Interrupt Management
If ADIE bit is set in register ADCCSR, an interrupt
is generated when a conversion is completed (i.e.
when COCO is set).
The interrupt request is cleared when any of the
ADC registers is access (either read or write).
Enabling/disabling the interrupt generation while
the conversion is running has no effect on the cur-
rent conversion. ADIE value is latched when
ADST is set and this internal value holds all the
conversion time long.
5.5.5 Temperature Sensing
The AD1 input is internally connected to the output
of a temperature sensing circuit.
The sensor generates a voltage proportional to the
absolute temperature of the die. It works over the
whole temperature range, with a minimum resolu-
tion of 1LSB/°K (5mV/°K) (
Figure 33
shows the in-
dicative voltage output of the sensor).
Note
The voltage output of the sensor is only relat-
ed to the absolute temperature of the silicon junc-
tions. Junction temperature and ambient tempera-
ture must be related taking in account the power
dissipated by the device and the thermal resist-
ance Rth
je
between the silicon and the environ-
ment around the application board.
Figure 33. Temperature Sensor output
V
TEMP
The output of the sensor is not ratiometric with the
voltage reference for the ADC conversion (VCC).
When calculating the ADC reading error of this sig-
nal the variation of VCC must be accounted. Addi-
tional errors are due to the intrinsic spread of the
sensor characteristic.
5.5.6 Precise Temperature Measurement
To allow a more precise measurement of the tem-
perature a trimming procedure can be adopted (on
request).
The temperature is measured in EWS and two val-
ues are stored in four EEPROM bytes (see memo-
ry map):
T0L,T0H: temperature of the trimming measure-
ment (in Kelvin).
VT0L,VT0H: output value of the ADC correspond-
ing to T0 (in number of LSBs).
The corrected measurement of the temperature
in
Kelvin
must be accomplished in the following way:
where VTEMP is the output code in LSB of the
ADC corresponding to the measurement.
Example:
If the value stored in EEPROM are:
0C7Ch: 01h ->T0H
0C7Dh: 43h ->T0L
0C7Eh: 01h -> VT0H
0C7Fh: 5Ch -> VT0L
T0 = 0143h = 323K (50 Celsius)
VTo = 015Ch = 348 LSB (conversion of 1.7V, sen-
sor output)
and the sensor output is 2V, converted by the ADC
in code 0110011001 = 019Ah = 410LSB, the tem-
perature of the chip is
TEMP = 019Ah * 0143h / 015Ch = 017Ch
equivalent to:
TEMP = 410 * 323 / 348 = 380 K = 107
°
C
Note
The sensor circuit may have two kind of er-
ror: one translating its output characteristic up and
down and the other changing its slope. The de-
scribed trimming recovers only the translation er-
rors but can not recover slope error. After trim-
ming, being T
TRIM
the trimming temperature, the
specified precision can be achieved in the range
T
TRIM
-80, max[T
TRIM
+80, 150
°
C]. Precision is re-
lated to the read temperature in Kelvin.
Temperature (°K)
1.0
2.5
1.3
1.6
1.9
2.2
273
323
373
223
max
min
TEMP (in °K) = VTEMP * T0 / VT0
相關PDF資料 |
PDF描述 |
|---|---|
| L9813 | SUPER SMART MIRROR WITH EMBEDDED MCU |
| L9820 | HIGH SIDE DRIVER |
| L9820D | HIGH SIDE DRIVER |
| L9822E | Octal Serial Solenoid Driver(八串行螺線管驅動器) |
| L9822ED | CAP CER 1000PF 1KVDC B RAD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9805E | 功能描述:馬達/運動/點火控制器和驅動器 Super Smart Power 8-Bit MCU, RAM RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9811 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Peripheral Driver |
| L9812R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Peripheral Driver |
| L9813 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SUPER SMART MIRROR WITH EMBEDDED MCU |
| L981CG-1 | 制造商:Thomas & Betts 功能描述:1/2 T CONDUIT BODY W/CVR & GASKET,E |
發布緊急采購，3分鐘左右您將得到回復。