- 您現在的位置：買賣IC網 > PDF目錄1961 > PI7C7300DNAE (Pericom)IC PCI-PCI BRIDGE 3PORT 272-BGA PDF資料下載
參數資料
| 型號： | PI7C7300DNAE |
| 廠商： | Pericom |
| 文件頁數： | 58/107頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PCI-PCI BRIDGE 3PORT 272-BGA |
| 標準包裝： | 40 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 272-BBGA |
| 供應商設備封裝： | 272-PBGA（27x27） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁
PI7C7300D
3-PORT PCI-TO-PCI BRIDGE
Page 54 of 107
Pericom Semiconductor
November 2005 - Revision 1.01
PI7C7300D asserts S_PERR# two cycles following the data transfer, if the
secondary interface parity error response bit is set in the bridge control register.
PI7C7300D sets the detected parity error bit in the secondary status register.
PI7C7300D sets the data parity detected bit in the secondary status register, if the
secondary interface parity error response bit is set in the bridge control register.
PI7C7300D forwards the bad parity with the data back to the initiator on the primary
bus. If the data with the bad parity is pre-fetched and is not read by the initiator on
the primary bus, the data is discarded and the data with bad parity is not returned to
the initiator.
PI7C7300D completes the transaction normally.
For upstream transactions, when PI7C7300D detects a read data parity error on the
primary bus, the following events occur:
PI7C7300D asserts P_PERR# two cycles following the data transfer, if the primary
interface parity error response bit is set in the command register.
PI7C7300D sets the detected parity error bit in the primary status register.
PI7C7300D sets the data parity detected bit in the primary status register, if the
primary interface parity-error-response bit is set in the command register.
PI7C7300D forwards the bad parity with the data back to the initiator on the
secondary bus. If the data with the bad parity is pre-fetched and is not read by the
initiator on the secondary bus, the data is discarded and the data with bad parity is
not returned to the initiator.
PI7C7300D completes the transaction normally.
PI7C7300D returns to the initiator the data and parity that was received from the target.
When the initiator detects a parity error on this read data and is enabled to report it, the
initiator asserts PERR# two cycles after the data transfer occurs. It is assumed that the
initiator takes responsibility for handling a parity error condition; therefore, when
PI7C7300D detects PERR# asserted while returning read data to the initiator,
PI7C7300D does not take any further action and completes the transaction normally.
7.2.3
DELAYED WRITE TRANSACTIONS
When PI7C7300D detects a data parity error during a delayed write transaction, the
initiator drives data and data parity, and the target checks parity and conditionally asserts
PERR#.
For delayed write transactions, a parity error can occur at the following times:
During the original delayed write request transaction
When the initiator repeats the delayed write request transaction
When PI7C7300D completes the delayed write transaction to the target
When a delayed write transaction is normally queued, the address, command, address
parity, data, byte enable bits, and data parity are all captured and a target retry is returned
to the initiator. When PI7C7300D detects a parity error on the write data for the initial
delayed write request transaction, the following events occur:
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C8140AMAE | IC PCI-PCI BRIDGE 2PORT 128-QFP |
| PI7C8150ANDE | IC PCI-PCI BRIDGE 2PORT 256-PBGA |
| PI7C8150BNDIE | IC PCI-PCI BRIDGE ASYNC 256-PBGA |
| PI7C8152BMAIE | IC PCI-PCI BRIDGE 2PORT 160-MQFP |
| PI7C8154ANAE | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C7300EVB | 功能描述:界面開發工具 3 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| PI7C8140A | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2 PORT PCI TO PCI BRIDGE PLX PCI 6140 COMPARISON |
| PI7C8140AEVB | 功能描述:界面開發工具 2 Port PCI to PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| PI7C8140AMA | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2-Port PCI-to-PCI Bridge |
| PI7C8140AMAE | 功能描述:外圍驅動器與原件 - PCI PCI -to -PCI Bridge 2 Port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。