- 您現在的位置：買賣IC網 > PDF目錄360706 > IBM32NPR101EPXCAC133 Microprocessor PDF資料下載
參數資料
| 型號： | IBM32NPR101EPXCAC133 |
| 英文描述： | Microprocessor |
| 中文描述： | 微處理器 |
| 文件頁數： | 89/131頁 |
| 文件大?。?/td> | 1679K |
| 代理商： | IBM32NPR101EPXCAC133 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁當前第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
PRS28.4G
IBM Packet Routing Switch
prs28.03.fm
August 31, 2000
Reset, Initialization, and Operation
Page 89 of 131
After configuration of the PLL Register (if necessary depending on use of internal or external PLL), the Clock
Start OCM Event is sent. This event causes the PLL Reset to be internally released when the internal PLL is
enabled. 100 microseconds after the PLL Reset has been released, the high speed DASL logic is automati-
cally placed in reset. If the internal PLL is not enabled, the DASL logic reset is sent just after the Clock Start
Event. After the DASL logic has been reset, the reset of the Clock/BIST/Flush-Reset is released, which
causes the internal Flush-Reset sequence to begin. The Status Register must be polled to determine when
the flush reset is complete.
In summary, the following steps must be taken to complete a Power-On-Reset of the device:
1. Assert nRESET for at least four EMB clock cycles.
2. Program the PLL Tune Bits via the PLL Register,
only
when using the internal PLL.
3. Issue a Clock Start OCM Event.
Check the Status Register bit 15 for completion of the Reset and Flush-Reset sequence. The first Response
to an OCM command after reset is undefined. Therefore, this data must be discarded and no checks
(including parity) should be performed on the first OCM Response.
6.2.2 Flush Reset and OCM_RESET Command
As mentioned above, the flush reset sequence is triggered automatically after a Power On Reset (nRESET)
and Clock Start OCM Event sequence. A flush reset can also be initiated by the OCM_RESET command
(Soft Reset).
All the core logic is reset via a flush reset (except the OCM, Clocks logic, BIST, Flush Reset logic, PLL, DASL
clock generation and macro, and JTAG logic). The scan chains are flushed with ‘0’b, and all other registers
and state machine are forced to their reset values.
The OCM_RESET command only starts the flush reset and does not cause any blocks (other than the one
touched by the flush reset) to be reset.
Bit 15 of the Status register is kept high as long as flush reset is active, and it is cleared when flush reset
completes.
The Flush Reset takes 1 ms to complete.
6.2.3 nTRST Primary Input Reset
The nTRST primary input must be asserted after a system power-on sequence. The nTRST input must be
kept active high during functional operation. During this time, the TMS primary input must be at a high voltage
level (‘1’b).
The nTRST input resets the JTAG logic block and is completely independent of all other reset sequences.
The JTAG logic can only be reset via the nTRST input, and the nTRST input has no effect on any other logic
block.
6.3 Initialization
The PRS28.4G device must be initialized after completion of a Power-On-Reset sequence, a Soft Reset, or a
Built In Self Test (BIST). These three events all cause the Flush Reset sequence to run. After completion of
the Flush Reset, the device is in a standby state. All outputs are tri-stated and data on all inputs is discarded.
相關PDF資料 |
PDF描述 |
|---|---|
| IBM37RGB524CF17A | Video DAC with Color Palette (RAMDAC) |
| IBM37RGB524CF22A | Video DAC with Color Palette (RAMDAC) |
| IBM39MPEGS420PBA18C | |
| IBM39MPEGS422PBA17C | |
| IBM39MPEGSIPBA18C | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBM35CPC945C03C-2 | 制造商:IBM 功能描述: |
| IBM37RGB524CF17A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC with Color Palette (RAMDAC) |
| IBM37RGB524CF22A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC with Color Palette (RAMDAC) |
| IBM39ENV422DLL00C | 制造商:IBM 功能描述: |
| IBM39ENV422PBA17C | 制造商:IBM Microelectronics 功能描述:VID ENCODER 420PIN HPBGA - Trays 制造商:IBM 功能描述:IBM IBM39ENV422PBA17C Encoders - Decoders |
發布緊急采購，3分鐘左右您將得到回復。