參數資料
型號: SIO10N268-NU
廠商: STANDARD MICROSYSTEMS CORP
元件分類: 外設及接口
英文描述: MULTIFUNCTION PERIPHERAL, PQFP128
封裝: 14 X 14 MM, 1MM THICKNESS, GREEN, TQFP-128
文件頁數: 243/251頁
文件大小: 1384K
代理商: SIO10N268-NU
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁當前第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁
Advanced Notebook I/O for ISA or LPC Designs
Datasheet
SMSC SIO10N268
Page 91
Rev. 0.5 (03-24-05)
DATASHEET
8.7.8.12 Enhanced DUMPREG
The DUMPREG command is designed to support system run-time diagnostics and application software
development and debug. To accommodate the LOCK command and the enhanced PERPENDICULAR
MODE command the eighth byte of the DUMPREG command has been modified to contain the additional
data from these two commands.
8.7.8.13 Compatibility
The SIO10N268 was designed with software compatibility in mind. It is a fully backwards- compatible
solution with the older generation 765A/B disk controllers. The FDC also implements on-board registers for
compatibility with the PS/2, as well as PC/AT and PC/XT, floppy disk controller subsystems. After a
hardware reset of the FDC, all registers, functions and enhancements default to a PC/AT, PS/2 or PS/2
Model 30 compatible operating mode, depending on how the IDENT and MFM bits are configured by the
system BIOS.
8.8
Serial Port (UART)
The SIO10N268 incorporates four full function UARTs. They are compatible with the 16450, the 16450
ACE registers and the 16C550A. The UARTS perform serial-to-parallel conversion on received characters
and parallel-to-serial conversion on transmit characters. The data rates are independently programmable
from 460.8K baud down to 50 baud. The character options are programmable for 1 start; 1, 1.5 or 2 stop
bits; even, odd, sticky or no parity; and prioritized interrupts. The UARTs each contain a programmable
baud rate generator that is capable of dividing the input clock or crystal by a number from 1 to 65535. The
UARTs are also capable of supporting the MIDI data rate. Refer to the Configuration Registers for
information on disabling, power down and changing the base address of the UARTs. The interrupt from
a UART is enabled by programming OUT2 of that UART to a logic "1". OUT2 being a logic "0" disables
that UART's interrupt. The second UART also supports IrDA 1.2 (4Mbps), HP-SIR, ASK-IR and Consumer
IR infrared modes of operation.
8.8.1
Register Description
Addressing of the accessible registers of the Serial Port is shown below. The base addresses of the serial
ports are defined by the configuration registers (see Configuration section). The Serial Port registers are
located at sequentially increasing addresses above these base addresses. The SIO10N268 contains two
serial ports, each of which contain a register set as described below.
Table 8.33 - Addressing the Serial Port
DLAB*
A2
A1
A0
REGISTER NAME
0
Receive Buffer (read)
0
Transmit Buffer (write)
0
1
Interrupt Enable (read/write)
X
0
1
0
Interrupt Identification (read)
X
0
1
0
FIFO Control (write)
X
0
1
Line Control (read/write)
X
1
0
Modem Control (read/write)
X
1
0
1
Line Status (read/write)
X
1
0
Modem Status (read/write)
X
1
Scratchpad (read/write)
1
0
Divisor LSB (read/write)
1
0
1
Divisor MSB (read/write
相關PDF資料
PDF描述
SIS300 GRAPHICS PROCESSOR, PBGA365
SK12430PJT 800 MHz, OTHER CLOCK GENERATOR, PQCC28
SK12439PJ 800 MHz, OTHER CLOCK GENERATOR, PQCC28
SK12439PJT 800 MHz, OTHER CLOCK GENERATOR, PQCC28
SL15100ZIT-XXX 200 MHz, OTHER CLOCK GENERATOR, PDSO8
相關代理商/技術參數
參數描述
SIO665GT 功能描述:界面開發工具 Evaluation Board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
SIO666GT 功能描述:界面開發工具 Evaluation Board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
SIO669 功能描述:界面開發工具 Evaluation Board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
SIOLS1000V2 制造商:SECELECTRONICS 制造商全稱:SECELECTRONICS 功能描述:Current Sensors
SIOLS2000V2 制造商:SECELECTRONICS 制造商全稱:SECELECTRONICS 功能描述:Current Sensors