- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC7032BSTZ-8V-RL (Analog Devices Inc)IC BATTERY SENSOR PREC 48-LQFP PDF資料下載
參數資料
| 型號： | ADUC7032BSTZ-8V-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 87/128頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC BATTERY SENSOR PREC 48-LQFP |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 連通性： | LIN，SPI，UART/USART |
| 外圍設備： | POR，PSM，溫度傳感器，WDT |
| 輸入/輸出數： | 9 |
| 程序存儲器容量： | 96KB（48K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1.5K x 32 |
| 電壓 - 電源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 數據轉換器： | A/D 2x16b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 105°C |
| 封裝/外殼： | 48-LQFP |
| 包裝： | 標準包裝 |
| 其它名稱： | ADUC7032BSTZ-8V-RLDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁當前第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Preliminary Technical Data
ADuC7032
Rev. PrD | Page 61 of 128
ADC Normal Power Mode
In Normal Mode, the Current and Voltage/Temperature
channels are fully enabled. The ADC modulator clock is
512KHz and enables the ADCs to provide regular conversion
results at a rate of between 4Hz and 8KHz (see ADCFLT). Both
channels are under full control of the MCU and can be
reconfigured at any time. The default ADC update rate for all
channels in this mode is 1.0kHz
It is worth emphasizing that I-ADC and V/T-ADC channels
can be configured to initiate periodic, normal power mode,
high accuracy, single conversion cycles before returning to
ADC full power-down mode. This flexibility is facilitated under
full MCU control via the ADCMDE MMR and ensures that
continuous periodic monitoring of battery current, voltage and
temperature settings is feasible while ensuring the average dc
current consumption is minimized.
In ADC Normal Mode, the PLL must not be powered down.
ADC Low Power Mode
In ADC Low Power mode, the I-ADC is enabled in a reduced
power and reduced accuracy configuration. The ADC
modulator clock is now driven directly from the on-chip
131KHz low power oscillator, which allows the ADC to be
configured at update rates as low as 1Hz(ADCFLT). The gain of
the ADC in this mode is fixed at 128.
All of the ADC peripheral functions (result counter, digital
comparator and accumulator) described earlier in normal
power mode can still be enabled in low power mode.
Typically, in Low Power Mode, the I-ADC only, is configured
to run at a low update rate, continuously monitoring battery
current. The MCU will be in power-down mode and will only
be woken up when the I-ADC interrupts the MCU. This would
happen after the I-ADC detects a current conversion or an
accumulated current value has risen beyond a pre-programmed
threshold, set-point or a set number of conversions.
It is also possible to select either the ADC Normal Mode
Voltage Reference of the ADC Low Power Mode Voltage
Reference via ADCMDE[5].
ADC Low Power-Plus Mode
In Low Power-Plus mode, the I-ADC channel is enabled in a
mode almost identical to low-power mode(ADCMDE[4:3]).
However, in this mode, the I-ADC gain is fixed at 512 and the
ADC consumes an additional 200uA (approx.) to yield
improved noise performance relative to the low-power mode
setting.
Again, all of the ADC peripheral functions (result counter,
digital comparator and accumulator) described earlier in
normal power mode can still be enabled in Low Power-Plus
mode.
As in Low Power Mode, the I-ADC only, is configured to run at
a low update rate, continuously monitoring battery current.
The MCU will be in power-down mode and will only be woken
up when the I-ADC interrupts the MCU. This would happen
after the I-ADC detects a current conversion result or an
accumulated current value has risen beyond a pre-programmed
threshold or set-point.
It is also possible to select either the ADC Normal Mode
Voltage Reference of the ADC Low Power Mode Voltage
Reference via ADCMDE[5].
ADC Sinc3 Digital Filter Response
The overall frequency response on all ADuC7032s ADCs is
dominated by the low pass filter response of the on-chip Sinc3
digital filters. The Sinc3 filters are used to decimate the ADC
sigma-delta modulator output data bit-stream to generate a
valid 16-bit data result. The digital filter response is identical
for all ADCs and is configured via the 16-bit ADC Filter
(ADCFLT) register which determines the overall throughput
rate of the ADCs. The noise resolution of the ADCs is
determined by the programmed ADC throughput rate. In the
case of the Current Channel ADC, the noise resolution will be
determined by throughput rate and selected gain.
The overall frequency response and the ADC through-put is
dominated by the configuration of the Sinc3 Filter Decimation
Factor (SF) bits (ADCFLT[6:0]) and the Averaging Factor (AF)
bits(ADCFLT[13:8]). Due to limitations on the digital filter
internal data-path, there are some limitations on the allowable
combinations
of
SF(Sinc3
Decimation
Factor)
and
AF(Averaging Factor) that can be used to generate a required
ADC output rate. This restriction limits the minimum ADC
update in Normal Power Mode to 4Hz or 1Hz in Low Power
Mode. The calculation of the ADC through-put rate is detailed
in the ADCFLT bit designations table and the restrictions on
allowable combinations of AF and SF values are outlined again
in Table 31
Table 31 : Allowable Combinations of SF and AF
AF Range
SF
0
1 to 7
8-63
<= 31
63
127
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC7034BCPZ | IC MCU FLASH 32K ANLG IO 48LFCSP |
| ADUC7036CCPZ | IC MCU 96K FLASH DUAL 48LFCSP |
| ADUC7039BCP6Z-RL | IC MCU ARM7 BATT SENSER 32LFCSP |
| ADUC7061BCPZ32 | IC MCU 16/32BIT 32KB 32LFCSP |
| ADUC7121BBCZ-RL | PRECISION ANALOG MCU I.C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7033 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive |
| ADUC7033BCPZ-8L | 制造商:Analog Devices 功能描述:Integrated Precision Battery Sensor 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Trays |
| ADUC7033BCPZ-8L-RL | 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Tape and Reel |
| ADUC7033BSTZ-88 | 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ADUC7033BSTZ-88-RL | 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。