參數資料
型號： ADUC7032BSTZ-8V-RL
廠商： Analog Devices Inc
文件頁數： 76/128頁
文件大?。?/td> 0K
描述： IC BATTERY SENSOR PREC 48-LQFP
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI，UART/USART
外圍設備： POR，PSM，溫度傳感器，WDT
輸入/輸出數： 9
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 105°C
封裝/外殼： 48-LQFP
包裝： 標準包裝
其它名稱： ADUC7032BSTZ-8V-RLDKR
Preliminary Technical Data
ADuC7032
Rev. PrD | Page 51 of 128
ADC Mode Register :
Name :
ADCMDE
Address :
0xFFFF0508
Default Value :
0x00
Access :
Read/Write
Function :
The ADC Mode MMR is an 8-bit register that configures the mode .of operation of the ADC sub-system
Table 23 : ADCMDE MMR Bit Designations
Bit
Description
7
Not Used
This bit is reserved for future functionality and be written as 0 by user code
6
20K
resistor select:
This bit is set to 1 to select the 20 K
resistor as shown in Figure 18
This bit is set to 0 to select the direct path to ground as shown in
Figure 18 ( Default ).
5
Low Power Mode Reference Select:
This bit is set to 1 to enable the Precision Voltage Reference in ADC Low Power Mode. This will increase current consumption.
This bit is set to 0 to enable the Low Power Voltage Reference in ADC Low Power Mode ( Default ).
4-3
ADC Power Mode Configuration
0, 0
ADC Normal Mode
If enabled, the ADC will operate with normal current consumption yielding optimum electrical performance
0, 1
ADC Low Power Mode
If enabled, the I-ADC will operate with reduced current consumption. This limitation is current consumption is
achieved, (at the expense of ADC noise performance) by fixing the gain to 128 and using the on-chip low power
(131kHz) oscillator to drive the ADC circuits directly.
1, 0
ADC Low Power-Plus Mode
If enabled, the ADC will again operate with reduced current consumption. In this mode the gain is fixed to 512 and
the current consumed is 200uA (approx.) more than ADC low Power Mode above. The additional current consumed
also ensures ADC noise performance is better than that achieved in ADC Low Power Mode.
1, 1
Not Defined
2-0
ADC Operation Mode Configuration
0, 0, 0 ADC Power-Down Mode
All ADC circuits (including internal reference) are powered-down
0, 0, 1 ADC Continuous Conversion Mode
In this mode, any enabled ADC will continuously convert.
0, 1, 0 ADC Single Conversion Mode
In this mode, any enabled ADC will perform a single conversion. The ADC will enter Idle Mode once the single
shot conversion is complete. A single conversion will take 2/3 ADC clock cycles depending on the CHOP mode.
0, 1, 1 ADC IDLE Mode
In this Mode, the ADC is fully powered on but is held in RESET
1, 0, 0 ADC Self-Offset Calibration
In this mode, an offset calibration is performed on any enabled ADC using an internally generated 0V. The
calibration is carried out at the user programmed ADC settings, therefore, as with a normal
single ADC
conversion, it will take 2/3 ADC conversion cycles before a fully settled calibration result is ready. The calibration
result is automatically written to the ADCxOF MMR of the respective ADC. The ADC returns to IDLE Mode and the
Calibration and Conversion Ready status bits are set at the end of an offset calibration cycle.
1, 0, 1 ADC Self Gain Calibration
In this mode, a gain calibration against an internal reference voltage is performed on all enabled ADCs. A gain
calibration is a 2 stage process and takes twice the time of an offset calibration. The calibration result is
automatically written to the ADCxGN MMR of the respective ADC. The ADC returns to IDLE Mode and the calibration
and Conversion Ready status bits are set at the end of an gain calibration cycle. An ADC self gain calibration should
only be carried out on the Current Channel ADC while pre-programmed, factory calibration coefficients (downloaded
automatically from internal Flash) should be used for voltage temperature measurements. If an external NTC is used,
an ADC Self Calibration should be done on the temperature channel.
相關PDF資料
PDF描述
ADUC7034BCPZ IC MCU FLASH 32K ANLG IO 48LFCSP
ADUC7036CCPZ IC MCU 96K FLASH DUAL 48LFCSP
ADUC7039BCP6Z-RL IC MCU ARM7 BATT SENSER 32LFCSP
ADUC7061BCPZ32 IC MCU 16/32BIT 32KB 32LFCSP
ADUC7121BBCZ-RL PRECISION ANALOG MCU I.C
相關代理商/技術參數
參數描述
ADUC7033 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive
ADUC7033BCPZ-8L 制造商:Analog Devices 功能描述:Integrated Precision Battery Sensor 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Trays
ADUC7033BCPZ-8L-RL 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Tape and Reel
ADUC7033BSTZ-88 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2
ADUC7033BSTZ-88-RL 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*