參數資料
型號： ADUC7032BSTZ-8V-RL
廠商： Analog Devices Inc
文件頁數： 45/128頁
文件大?。?/td> 0K
描述： IC BATTERY SENSOR PREC 48-LQFP
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI，UART/USART
外圍設備： POR，PSM，溫度傳感器，WDT
輸入/輸出數： 9
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 105°C
封裝/外殼： 48-LQFP
包裝： 標準包裝
其它名稱： ADUC7032BSTZ-8V-RLDKR
Preliminary Technical Data
ADuC7032
Rev. PrD | Page 23 of 128
PIN FUNCTION DESCRIPTIONS
Table 7: Pin Function Descriptions
Pin#
Mnemonic
Type*
Function
1
RESET
I
Reset Input Pin, Active Low. This pin has an internal, weak pull-up resistor to
REG_DVDD. If this pin is not being used it can be left not connected. For
added security and robustness, it is recommended that this pin be strapped
via a resistor to REG_DVDD.
2
GPIO_5/IRQ1/RxD
I/O
General Purpose Digital I/O 5 is a Multi-Function Pin. By default and after
Power-On-Reset, this pin is configured as an input. The pin has an internal
weak pull-up resistor and if not being used it can be left unconnected. This
multi-function pin can be configured in one of 3 states, namely:
General Purpose Digital I/O 5
External Interrupt Request 1, Active High
Receive Data for UART Serial Port
This Pin may also be used as a clock input to Timer1.
3
GPIO_6/TxD
I/O
General Purpose Digital I/O 6 is a Multi-Function Pin. By default and after
Power-On-Reset, this pin is configured as an input. The pin has an internal
weak pull-up resistor and if not being used it can be left unconnected. This
multi-function pin can be configured in one of 2 states, namely:
General Purpose Digital I/O 6
Transmit Data for UART Serial Port
4
GPIO_7/IRQ4
I/O
General Purpose Digital I/O 7 is a multi-function pin. By default and after
Power-On-Reset, this pin is configured as an input. The pin has an internal
weak pull-up resistor and if not being used it can be left unconnected. This
multi-function pin can be configured in one of 2 states, namely:
General Purpose Digital I/O 7
External Interrupt Request 4, Active High
5
GPIO_8/ IRQ5
I/O
General Purpose Digital I/O 8 is a multi-function pin. By default and after
Power-On-Reset, this pin is configured as an input. The pin has an internal
weak pull-up resistor and if not being used it can be left unconnected. This
multi-function pin can be configured in one of 2 states, namely:
General Purpose Digital I/O 8
External Interrupt Request 5, Active High
This Pin may also be used as a clock input to Timer1.
6
TCK
I
JTAG Test Clock. This clock input pin is one of the standard 5 pin JTAG debug
port on the part. TCK is an input pin only and has an internal weak pull-up
resistor. If not being used this pin can be left unconnected
7
TDI
I
JTAG Test Data Input. This data input pin is one of the standard 5 pin JTAG
debug port on the part. TDI is an input pin only and has an internal weak pull-
up resistor. If not being used this pin can be left unconnected
8
DGND
S
Ground Reference for On-Chip Digital Circuits
9
NC
No Connect, this pin is not connected internally but is reserved for possible
future use, this pin should therefore not be connected externally
10
TDO
O
JTAG Test Data Output. This data output pin is one of the standard 5 pin JTAG
debug port on the part. TDO is an output pin only. On power-on this output is
disabled and pulled high via an internal weak pull-up resistor. If not being
used this pin can be left unconnected
11
NTRST
I
JTAG Test Reset. This Reset input pin is one of the standard 5 pin JTAG debug
port on the part. NTRST is an input pin only and has an internal weak pull-
down resistor. If not being used this pin can be left unconnected. NTRST is
also monitored by the on-chip kernel to enable LIN boot-load mode.
12
TMS
I
JTAG Test Mode Select. This Mode Select input pin is one of the standard 5
pin JTAG debug port on the part. TMS is an input pin only and has an internal
weak pull-up resistor. If not being used this pin can be left unconnected
相關PDF資料
PDF描述
ADUC7034BCPZ IC MCU FLASH 32K ANLG IO 48LFCSP
ADUC7036CCPZ IC MCU 96K FLASH DUAL 48LFCSP
ADUC7039BCP6Z-RL IC MCU ARM7 BATT SENSER 32LFCSP
ADUC7061BCPZ32 IC MCU 16/32BIT 32KB 32LFCSP
ADUC7121BBCZ-RL PRECISION ANALOG MCU I.C
相關代理商/技術參數
參數描述
ADUC7033 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive
ADUC7033BCPZ-8L 制造商:Analog Devices 功能描述:Integrated Precision Battery Sensor 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Trays
ADUC7033BCPZ-8L-RL 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Tape and Reel
ADUC7033BSTZ-88 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2
ADUC7033BSTZ-88-RL 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*