- 您現在的位置：買賣IC網 > PDF目錄25640 > S1C63158D0A010P 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, UUC53 PDF資料下載
參數資料
| 型號： | S1C63158D0A010P |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, UUC53 |
| 封裝： | DIE-53 |
| 文件頁數： | 38/159頁 |
| 文件大?。?/td> | 1200K |
| 代理商： | S1C63158D0A010P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁
124
EPSON
S1C63808 TECHNICAL MANUAL
CHAPTER 5: SUMMARY OF NOTES
Output port
(1) When using the output port (R01, R02, R03) as the special output port (BZ, TOUT, FOUT), fix the data
register (R01, R02, R03) at "1" and the high impedance control register (R01HIZ, R02HIZ, R03HIZ) at
"0" (data output).
Be aware that the output terminal is fixed at a low (VSS) level the same as the DC output if "0" is
written to the R01, R02 and R03 registers when the special output has been selected.
Be aware that the output terminal shifts into high impedance status when "1" is written to the high
impedance control register (R01HIZ, R02HIZ, R03HIZ).
(2) A hazard may occur when the BZ signal, FOUT signal and the TOUT signal are turned on and off.
(3) When fOSC3 is selected for the FOUT signal frequency, it is necessary to control the OSC3 oscillation
circuit before output.
Refer to Section 4.3, "Oscillation Circuit", for the control and notes.
I/O port
When in the input mode, I/O ports are changed from high to low by pull-down resistor, the fall of the
waveform is delayed on account of the time constant of the pull-down resistor and input gate capaci-
tance. Hence, when fetching input ports, set an appropriate wait time.
Particular care needs to be taken of the key scan during key matrix configuration.
Make this waiting time the amount of time or more calculated by the following expression.
10
× C × R
C: terminal capacitance 5 pF + parasitic capacitance ? pF
R: pull-down resistance 375 k
(Max.)
Clock timer
Be sure to read timer data in the order of low-order data (TM0–TM3) then high-order data (TM4–TM7).
Stopwatch timer
(1) The interrupt factor flag should be reset after resetting the stopwatch timer.
(2) Be sure to data reading in the order of SWD0–3
→ SWD4–7 → SWD8–11.
(3) When data that is held by a LAP input is read, read the capture buffer renewal flag CRNWF after
reading the SWD8–11 and check whether the data has been renewed or not.
(4) When performing a processing such as a LAP input preceding with 1 Hz interrupt processing, read the
LAP data carry-up request flag LCURF before processing and check whether carry-up is needed or not.
Programmable timer
(1) When reading counter data, be sure to read the low-order 4 bits (PTDx0–PTDx3) first. Furthermore,
the high-order 4 bits (PTDx4–PTDx7) should be read within 0.73 msec (when fOSC1 is 32.768 kHz) of
reading the low-order 4 bits (PTDx0–PTDx3).
The counter data in 16-bit mode must be read in the order below.
PTD00–PTD03
→ PTD04–PDT07 → PTD10–PTD13 → PTD14–PTD17
(2) The programmable timer actually enters RUN/STOP status in synchronization with the falling edge
of the input clock after writing to the PTRUNx register. Consequently, when "0" is written to the
PTRUNx register, the timer enters STOP status at the point where the counter is decremented (-1).
The PTRUNx register maintains "1" for reading until the timer actually stops.
Figure 5.2.1 shows the timing chart for the RUN/STOP control.
PTRUNx (WR)
PTDx0–PTDx7
42H
41H 40H 3FH 3EH
3DH
PTRUNx (RD)
Input clock
"1" (RUN)
writing
"0" (STOP)
writing
Fig. 5.2.1 Timing chart for RUN/STOP control
It is the same even in the event counter mode. Therefore, be aware that the counter does not enter
RUN/STOP status if a clock is not input after setting the RUN/STOP control register (PTRUN0).
相關PDF資料 |
PDF描述 |
|---|---|
| S1C7XXXF00E199 | 16-BIT, 90 MHz, RISC MICROCONTROLLER, PQFP |
| S2041 | PHOTO TRANSISTOR DETECTOR |
| S3P44R10 | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
| S3S12P128J0VQK | 16-BIT, MROM, 1.05 MHz, MICROCONTROLLER, PQFP80 |
| MC9S12P128J0CFTR | 16-BIT, FLASH, 1.05 MHz, MICROCONTROLLER, QCC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63408 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。