- 您現在的位置：買賣IC網 > PDF目錄25640 > S1C63158D0A010P 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, UUC53 PDF資料下載
參數資料
| 型號： | S1C63158D0A010P |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, UUC53 |
| 封裝： | DIE-53 |
| 文件頁數： | 124/159頁 |
| 文件大?。?/td> | 1200K |
| 代理商： | S1C63158D0A010P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁當前第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁
S1C63808 TECHNICAL MANUAL
EPSON
59
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Stopwatch Timer)
IRUN, ILAP, ISW1, ISW10: Interrupt factor flags (FFF8H)
These flags indicate the status of the stopwatch timer interrupt.
When "1" is read: Interrupt has occurred
When "0" is read: Interrupt has not occurred
When "1" is written: Flag is reset
When "0" is written: Invalid
The interrupt factor flags IRUN, ILAP, ISW1 and ISW10 correspond to the direct RUN, direct LAP, 1 Hz
and 10 Hz interrupts respectively. The software can judge from these flags whether there is a stopwatch
timer interrupt. However, even if the interrupt is masked, the flags are set to "1" when the timing condi-
tion is established.
These flags are reset to "0" by writing "1" to them.
After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag = "1") is
set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure to reset
(write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the interrupt
enabled state.
At initial reset, these flags are set to "0".
4.8.8 Programming notes
(1) The interrupt factor flag should be reset after resetting the stopwatch timer.
(2) Be sure to data reading in the order of SWD0–3
→ SWD4–7 → SWD8–11.
(3) When data that is held by a LAP input is read, read the capture buffer renewal flag CRNWF after
reading the SWD8–11 and check whether the data has been renewed or not.
(4) When performing a processing such as a LAP input preceding with 1 Hz interrupt processing, read
the LAP data carry-up request flag LCURF before processing and check whether carry-up is needed or
not.
(5) After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag =
"1") is set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure
to reset (write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the
interrupt enabled state.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C7XXXF00E199 | 16-BIT, 90 MHz, RISC MICROCONTROLLER, PQFP |
| S2041 | PHOTO TRANSISTOR DETECTOR |
| S3P44R10 | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
| S3S12P128J0VQK | 16-BIT, MROM, 1.05 MHz, MICROCONTROLLER, PQFP80 |
| MC9S12P128J0CFTR | 16-BIT, FLASH, 1.05 MHz, MICROCONTROLLER, QCC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63408 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。