- 您現在的位置：買賣IC網 > PDF目錄25640 > S1C63158D0A010P 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, UUC53 PDF資料下載
參數資料
| 型號： | S1C63158D0A010P |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, UUC53 |
| 封裝： | DIE-53 |
| 文件頁數： | 37/159頁 |
| 文件大?。?/td> | 1200K |
| 代理商： | S1C63158D0A010P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁
S1C63808 TECHNICAL MANUAL
EPSON
123
CHAPTER 5: SUMMARY OF NOTES
5.2 Summary of Notes by Function
Here, the cautionary notes are summed up by function category. Keep these notes well in mind when
programming.
Memory and stack
(1)Memory is not implemented in unused areas within the memory map. Further, some non-implemen-
tation areas and unused (access prohibition) areas exist in the peripheral I/O area. If the program that
accesses these areas is generated, its operation cannot be guaranteed. Refer to the I/O memory maps
shown in Table 4.1.1 for the peripheral I/O area.
(2) Part of the RAM area is used as a stack area for subroutine call and register evacuation, so pay
attention not to overlap the data area and stack area.
(3) The S1C63000 core CPU handles the stack using the stack pointer for 4-bit data (SP2) and the stack
pointer for 16-bit data (SP1).
16-bit data are accessed in stack handling by SP1, therefore, this stack area should be allocated to the
area where 4-bit/16-bit access is possible (0100H to 01FFH). The stack pointers SP1 and SP2 change
cyclically within their respective range: the range of SP1 is 0000H to 03FFH and the range of SP2 is
0000H to 00FFH. Therefore, pay attention to the SP1 value because it may be set to 0200H or more
exceeding the 4-bit/16-bit accessible range in the S1C63808 or it may be set to 00FFH or less. Memory
accesses except for stack operations by SP1 are 4-bit data access. After initial reset, all the interrupts
including NMI are masked until both the stack pointers SP1 and SP2 are set by software. Further, if
either SP1 or SP2 is re-set when both are set already, the interrupts including NMI are masked again
until the other is re-set. Therefore, the settings of SP1 and SP2 must be done as a pair.
Watchdog timer
(1) When the watchdog timer is being used, the software must reset it within 3-second cycles.
(2) Because the watchdog timer is set in operation state by initial reset, set the watchdog timer to disabled
state (not used) before generating an interrupt (NMI) if it is not used.
Oscillation circuit
(1) It takes at least 5 msec from the time the OSC3 oscillation circuit goes on until the oscillation stabi-
lizes. Consequently, when switching the CPU operation clock from OSC1 to OSC3, do this after a
minimum of 5 msec have elapsed since the OSC3 oscillation went on.
Further, the oscillation stabilization time varies depending on the external oscillator characteristics
and conditions of use, so allow ample margin when setting the wait time.
(2) When switching the clock form OSC3 to OSC1, use a separate instruction for switching the OSC3
oscillation off. An error in the CPU operation can result if this processing is performed at the same
time by the one instruction.
Input port
When input ports are changed from high to low by pull-down resistors, the fall of the waveform is
delayed on account of the time constant of the pull-down resistor and input gate capacitance. Hence,
when fetching input ports, set an appropriate waiting time. Particular care needs to be taken of the
key scan during key matrix configuration. Make this waiting time the amount of time or more calcu-
lated by the following expression.
10
× C × R
C: terminal capacitance 5 pF + parasitic capacitance ? pF
R: pull-down resistance 375 k
(Max.)
相關PDF資料 |
PDF描述 |
|---|---|
| S1C7XXXF00E199 | 16-BIT, 90 MHz, RISC MICROCONTROLLER, PQFP |
| S2041 | PHOTO TRANSISTOR DETECTOR |
| S3P44R10 | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
| S3S12P128J0VQK | 16-BIT, MROM, 1.05 MHz, MICROCONTROLLER, PQFP80 |
| MC9S12P128J0CFTR | 16-BIT, FLASH, 1.05 MHz, MICROCONTROLLER, QCC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63408 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。