參數資料
型號: MC16V1CPU20B1
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 16-BIT, MROM, 20.97 MHz, MICROCONTROLLER, PQFP100
封裝: TQFP-100
文件頁數: 38/128頁
文件大小: 571K
代理商: MC16V1CPU20B1
MC68HC16V1
MOTOROLA
MC68HC16V1TS/D
17
The sub-module disable register (SMD) is used to disable sub-modules within the SLIM when they are
not in use. A sub-module is disabled when its corresponding bit is set to one. Disabling the sub-module
prevents it from being clocked, thereby placing the sub-module in its lowest power consumption state.
BRKEN — Breakpoint Enable
When enabled, this bit asserts BKPT on the IMB when any of the chip-select match signals is true, plac-
ing the CPU16 into background debug mode. This allows the user to breakpoint on addresses and con-
ditions specified in the chip-select registers.
0 = Breakpoint logic is disabled
1 = Breakpoint logic is enabled
CHIP SELECT — Chip-Select Disable
0 = Chip-select sub-module is enabled
1 = Chip-select sub-module is disabled
TEST —Test Disable
0 = Test sub-module is enabled
1 = Test sub-module is disabled
SYSPROT— System Protect Disable
Disabling the system protection sub-module prevents the software watchdog timer, real time clock,
prescaler, bus monitor, spurious interrupt monitor, and halt monitor from functioning.
0 = System protection sub-module is enabled
1 = System protection sub-module is disabled
The port/clock configuration shadow register (PCON) is a mask programmable register that determines
the default reset value of corresponding bits and fields in the port C, D, and E pin assignment registers,
as well as the default clock configuration. Refer to Table 10.
During reset, the specified configuration is loaded based on the information programmed in PCON at
mask time. Driving DRCD to a logic level zero when RESET is asserted overrides the configuration in
PCON for some port pin assignment bits and the clock select. This allows them to be configured from
outside the device by the state driven on certain SLIM pins during reset. Not all bits in the port pin as-
signment registers have corresponding shadow bits in PCON.
NOTE
PCON programming must be consistent with pin availability. If a pin does not exist
on the device, PCON bits should be programmed to configure the pin function as
digital I/O out of reset, since EBI operation can be affected by the presence or ab-
sence of these pins. Refer to Table 1 for the factory specified PCON value appro-
priate to the MCU package being used.
PCON — Port/Clock Configuration Shadow Register
$YFFA0E
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
PCON[13:11]
PCON[10:9]
PCON[8:7]
PCON[6:5]
PCON4 PCON3 PCON2 PCON1 PCON0
RESET:
USER SPECIFIED
相關PDF資料
PDF描述
MC2670L DOT MAT LCD DRVR AND DSPL CTLR, CDIP28
MC2670P DOT MAT LCD DRVR AND DSPL CTLR, PDIP28
MC2671AS 1 CHANNEL(S), SERIAL COMM CONTROLLER, CDIP40
MC2671AL 1 CHANNEL(S), SERIAL COMM CONTROLLER, CDIP40
MC2675B5S SPECIALTY MICROPROCESSOR CIRCUIT, CDIP40
相關代理商/技術參數
參數描述
MC16XSD200FK 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Dual 16 mOhm High Side Switch
MC16Z1CFC25B1 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC16Z1CPV20B1 制造商:Rochester Electronics LLC 功能描述:16 BIT MCU, 1K RAM - Bulk
MC16Z3BCAG16 功能描述:16位微控制器 - MCU 16BIT MCU 4KRAM 8KROM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC-17 功能描述:TERM BARRIER 17CIRC DUAL ROW RoHS:是 類別:連接器,互連式 >> 接線座 - 隔板塊 系列:M 標準包裝:10 系列:Beau™ 38780 端接塊類型:阻隔塊 電路數:15 導線入口數目:30 間距:0.438"(11.12mm) 行數:2 電流:15A 電壓:300V 線規:14-22 AWG 頂部端子:螺釘 底部端子:焊片 阻擋層類型:雙壁(雙) 特點:法蘭 顏色:黑 包裝:散裝 安裝類型:通孔 工作溫度:- 材料 - 絕緣體:聚對苯二甲酸丁二酯(PBT),玻璃纖維增強型 材料可燃性額定值:UL94 V-0 其它名稱:038780-111538780-1115387801115