參數資料
型號: ZPSD813F1V
英文描述: Flash In System Programmable Mirocomputer Peripherals(閃速,在系統可編程微控制器外圍器件,1M位閃速存儲器,256K位EEPROM,16K位SRAM)
中文描述: Flash在系統可編程Mirocomputer外設(閃速,在系統可編程微控制器外圍器件,100萬位閃速存儲器,256K位的EEPROM,16K的位的SRAM)
文件頁數: 59/130頁
文件大?。?/td> 650K
代理商: ZPSD813F1V
Prelimnary
PSD813F Famly
55
The
PSD813F
Functional
Blocks
(cont.)
9.4 I/OPorts
There are four programmable I/O ports: Ports A, B, C, and D. Each of the ports is eight bits
except Port D, which is 3 bits. Each port pin is individually user configurable, thus allowing
multiple functions per port. The ports are configured using PSDsoft Configuration or by the
microcontroller writing to on-chip registers in the CSIOP address space.
The topics discussed in this section are:
General Port Architecture
Port Operating Modes
Port Configuration Registers
Port Data Registers
Individual Port Functionality.
9.4.1 General Port Architecture
The general architecture of the I/O Port is shown in Figure 25. Individual Port architectures
are shown in Figures 27 through 30. In general, once the purpose for a port pin has been
defined, that pin will no longer be available for other purposes. Exceptions will be noted.
As shown in Figure 25, the ports contain an output multiplexer whose selects are driven
by the configuration bits in the Control Registers (Ports A and B only) and PSDsoft
Configuration. Inputs to the multiplexer include the following:
J
Output data from the Data Out Register
J
Latched address outputs
J
CPLD Micro
Cell output
J
External Chip Select from CPLD.
The Port Data Buffer (PDB) is a tri-state buffer that allows only one source at a time to be
read. The PDB is connected to the Internal Data Bus for feedback and can be read by the
microcontroller. The Data Out and Micro
Cell outputs, Direction and Control Registers,
and port pin input are all connected to the PDB.
The Port pin’s tri-state output driver enable is controlled by a two input OR gate whose
inputs come from the CPLD AND array enable product term and the Direction Register. If
the enable product term of any of the array outputs are not defined and that port pin is not
defined as a CPLD output in the PSDabel file, then the Direction Register has sole control
of the buffer that drives the port pin.
The contents of these registers can be altered by the microcontroller. The PDB feedback
path allows the microcontroller to check the contents of the registers.
Ports A, B, and C have embedded Input Micro
Cells (IMCs). The IMCs can be configured
as latches, registers, or direct inputs to the PLDs. The latches and registers are clocked by
the address strobe (AS/ALE) or a product term from the PLD AND array. The outputs from
the IMCs drive the PLD input bus and can be read by the microcontroller. Refer to the IMC
subsection of the PLD section.
相關PDF資料
PDF描述
ZR33771GC-40 Cell Rectifier Diodes
ZR33771GM-20 Cell Rectifier Diodes
ZR33771GM-30 Cell Rectifier Diodes
ZR33771GM-40 Cell Rectifier Diodes
ZR33771PQC-20 Cell Rectifier Diodes
相關代理商/技術參數
參數描述
ZPSD813F1V-15J 制造商:WSI 功能描述:
ZPSD813F1V-15J-CC790 制造商:STMicroelectronics 功能描述:Flash In SystemProgrammable Mirocomputer Peripherals
ZPSD813F1V-20J 制造商:WSI 功能描述:
ZPSD813F2-12JI 制造商:WSI 功能描述: 制造商:WSI 功能描述:1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52
ZPSD813F2-12UI 制造商:WSI 功能描述: 制造商:WSI 功能描述:1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP64