- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C88104P0A0100 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, PBGA240 PDF資料下載
參數資料
| 型號： | S1C88104P0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, PBGA240 |
| 封裝： | VFBGA10H-216 |
| 文件頁數： | 172/211頁 |
| 文件大?。?/td> | 1802K |
| 代理商： | S1C88104P0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁當前第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁
S1C8F626 TECHNICAL MANUAL
EPSON
55
5 PERIPHERAL CIRCUITS AND THEIR OPERATION (Serial Interface)
5.7.5 Transmit-receive control
Below is a description of the registers which handle
transmit-receive control. With respect to transmit-
receive control procedures and operations, please
refer to the following sections in which these are
discussed on a mode by mode basis.
■ Shift register and received data buffer
Exclusive shift registers for transmitting and
receiving are installed in this serial interface.
Consequently, duplex communication simulta-
neous transmit and receive is possible when the
asynchronous system is selected.
Data being transmitted are written to TRXDx0–
TRXDx7 and converted to serial through the shift
register and is output from the SOUTx terminal.
In the reception section, a received data buffer is
installed separate from the shift register.
Data being received are input to the SINx terminal
and is converted to parallel through the shift
register and written to the received data buffer.
Since the received data buffer can be read even
during serial input operation, the continuous data
is received efficiently.
However, since buffer functions are not used in
clock synchronous mode, be sure to read out data
before the next data reception begins.
■ Transmit enable register and transmit
control bit
For transmitting control, use the transmit enable
register TXENx and transmit control bit TXTRGx.
The transmit enable register TXENx is used to set
the transmitting enable/disable status. When "1" is
written to this register to set the transmitting enable
status, clock input to the shift register is enabled
and the system is ready to transmit data. In the
clock synchronous mode, synchronous clock input/
_________
output from the SCLKx terminal is also enabled.
The transmit control bit TXTRGx is used as the
trigger to start transmitting data.
Data to be transmitted is written to the transmit
data shift register, and when transmitting prepara-
tions a recomplete, "1" is written to TXTRGx
whereupon data transmitting begins.
When interrupt has been enabled, an interrupt is
generated when the transmission is completed. If
there is subsequent data to be transmitted it can be
sent using this interrupt.
In addition, TXTRGx can be read as the status.
When set to "1", it indicates transmitting operation,
and "0" indicates transmitting stop.
For details on timing, see the timing chart which
gives the timing for each mode.
When not transmitting, set TXENx to "0" to disable
transmitting status.
■ Receive enable register and receive control
bit
For receiving control, use the receive enable register
RXENx and receive control bit RXTRGx.
Receive enable register RXENx is used to set
receiving enable/disable status. When "1" is written
into this register to set the receiving enable status,
clock input to the shift register is enabled and the
system is ready to receive data. In the clock syn-
chronous mode, synchronous clock input/output
_________
from the SCLKx terminal is also enabled.
With the above setting, receiving begins and serial
data input from the SINx terminal goes to the shift
register.
The operation of the receive control bit RXTRGx is
slightly different depending on whether a clock
synchronous system or an asynchronous system is
being used.
In the clock synchronous system, the receive
control bit RXTRGx is used as the trigger to start
receiving data.
When received data has been read and the prepara-
tion for next data receiving is completed, write "1"
into RXTRGx to start receiving. (When "1" is written
_________
to RXTRGx in slave mode, SRDYx switches to "0".)
In an asynchronous system, RXTRGx is used to
prepare for next data receiving. After reading the
received data from the received data buffer, write
"1" into RXTRGx to signify that the received data
buffer is empty. If "1" is not written into RXTRGx,
the overrun error flag OERx will be set to "1" when
the next receiving operation is completed. (An
overrun error will be generated when receiving is
completed between reading the received data and
the writing of "1" to RXTRGx.)
In addition, RXTRGx can be read as the status. In
either clock synchronous mode or asynchronous
mode, when RXTRGx is set to "1", it indicates
receiving operation and when set to "0", it indicates
that receiving has stopped.
For details on timing, see the timing chart which
gives the timing for each mode.
When you do not receive, set RXENx to "0" to
disable receiving status.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C88317D0A0100 | MICROCONTROLLER, UUC170 |
| S1C88308D0A0100 | MICROCONTROLLER, UUC170 |
| S1C88308F0A0100 | MICROCONTROLLER, PQFP160 |
| S1C88348F | 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, PQFP16 |
| S1C88316D | 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC172 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C88349 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88649 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88650 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88655 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88816 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。