- 您現在的位置：買賣IC網 > PDF目錄1916 > DS34S132GN+ (Maxim Integrated Products)IC TDM OVER PACKET 676-BGA PDF資料下載
參數資料
| 型號： | DS34S132GN+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 138/194頁 |
| 文件大小： | 0K |
| 描述： | IC TDM OVER PACKET 676-BGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 40 |
| 功能： | TDM-over-Packet（TDMoP） |
| 接口： | TDMoP |
| 電路數： | 1 |
| 電源電壓： | 1.8V, 3.3V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 676-BGA |
| 供應商設備封裝： | 676-PBGA（27x27） |
| 包裝： | 管件 |
| 其它名稱： | 90-34S13+2N0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁當前第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁
DS34S132 DATA SHEET
19-4750; Rev 1; 07/11
48 of 194
The PDVT setting specifies how much data must be stored by the Jitter Buffer before “play-out” (FIFO read) begins.
After “play-out” begins the Jitter Buffer will continue to supply data until the Jitter Buffer is empty. If the Jitter Buffer
empties, then the Jitter Buffer must again fill to the PDVT level before data will again be forwarded.
The MJBS watermark can be used to indicate when the level of stored data exceeds an “expected” maximum
(overrun) level. This can be used to monitor for “unexpected” fill levels (e.g. too much data accumulated because of
improperly configured input or output clocks or if the MJBS setting does not allow for the maximum PDV). MJBS
can be monitored to implement a discard process that prevents each Bundle’s Jitter Buffer from over-filling and
adding to the latency of the data (some Clock Recovery Engine firmware revisions may include a function to
discard Jitter Buffer data when MJBS indicates the Jitter Buffer has too much data). The MJBS register should be
programmed to a level that is lower than the JBMD level so that an MJBS Overrun condition can be detected before
JBMD discarding begins. Figure 9-16 depicts the relationship between the JBMD, MJBS and PDVT settings (the
blue area depicts data that is stored in the Jitter Buffer FIFO).
Figure 9-16. Bundle Jitter Buffer FIFO
MJBS
PDVT
JBMD
This area is empty and
can store SAT/CES TDM
Data from RXP packets.
This area is filled with
SAT/CES TDM Data that
is waiting to be transmited
on the TDM line.
If the SAT/CES TDM Data exceeds the
MJBS Watermark, a Jitter Buffer
Overrun event is counted
(B.BDSR2.JEBEC).
SAT/CES TDM Data is not forwarded to
the TDM Line until the fill level exceeds
the PDVT Watermark.
If the SAT/CES TDM Data exceeds the
JBMD level data, new data is discarded.
Bundle Jitter Buffer FIFO
New SAT/CES packet data is stored here
SAT/CES data is read out from here and sent to TDM Port
The purpose of the Jitter Buffer is to store data that can be transmitted during time periods when the S132 must
wait for a packet that has been “delayed”. At the receiving end of a PW, when a packet is received the PW end
point cannot know whether the PDV for that packet was “zero”, the maximum PDV value or any value in between.
If the receiving PW end point knew that the PDV for a received packet was zero, then the best situation would be to
begin storing data and not forward that data until a time period equal to the maximum PDV. Or, if the PW end point
instead knew that a packet was received with the maximum PDV, then the best situation would be to immediately
forward the data (data will never come later than the maximum PDV; storing would add unnecessary delay).
However the PW end point does not know the PDV level for each packet and thereby must make an assumption.
There are three approaches for setting the PDVT and MJBS values. Each system should be analyzed to determine
which approach is preferred. In each of these approaches the minimum Jitter Buffer delay is equal to the PDVT
setting, while the maximum Jitter Buffer delay (maximum fill level) is either equal to the MJBS or JBMD setting
(MJBS is the maximum if MJBS is monitored as a watermark for discarding; otherwise the maximum is JBMD).
The first approach assumes that it is important to never discard data. This approach results in “2 * Total PDV” ≤
“Jitter Buffer Delay” ≤ “MJBS or JBMD”. This may be the most commonly used setting for existing/installed TDM
over PW services. The settings for this approach are specified by the following equations:
PDVT1 (in ms) = 2 * Total PDV (in ms)
MJBS1 (in ms) = PCT (in ms) + 2 * Total PDV (in ms)
The PCT value is included as part of the MJBS setting to provide a watermark condition that is slightly higher than
the PDVT (playout) watermark and because the originating and terminating ends of the PW cannot be perfectly
phase synchronized together. When the PCT is included as part of the MJBS value, in most cases, the S132 fixed
circuit processing delays can be disregarded (included as part of the PCT value, e.g. BFD PDV).
The second approach assumes that delay must be minimized and only a small amount of discarding should be
allowed. This approach results in a temporary, maximum latency = “2 PDV + PCT”. But as the PDV varies from its
相關PDF資料 |
PDF描述 |
|---|---|
| DS34T102GN+ | IC TDM OVER PACKET 484TEBGA |
| DS3501U+H | IC POT NV 128POS HV 10-USOP |
| DS3502U+ | IC POT DGTL NV 128TAP 10-MSOP |
| DS3503U+ | IC POT DGTL NV 128TAP 10-MSOP |
| DS3897MX | IC TXRX BTL TRAPEZIODAL 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS34S132GN+ | 功能描述:通信集成電路 - 若干 32Port TDM-Over-Pack Transport Device RoHS:否 制造商:Maxim Integrated 類型:Transport Devices 封裝 / 箱體:TECSBGA-256 數據速率:100 Mbps 電源電壓-最大:1.89 V, 3.465 V 電源電壓-最小:1.71 V, 3.135 V 電源電流:50 mA, 225 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| DS34S132GNA2+ | 功能描述:通信集成電路 - 若干 32Port TDM-Over-Pack Transport Device RoHS:否 制造商:Maxim Integrated 類型:Transport Devices 封裝 / 箱體:TECSBGA-256 數據速率:100 Mbps 電源電壓-最大:1.89 V, 3.465 V 電源電壓-最小:1.71 V, 3.135 V 電源電流:50 mA, 225 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| DS34T101 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual/Quad/Octal TDM-over-Packet Chip |
| DS34T101_08 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual/Quad/Octal TDM-over-Packet Chip |
| DS34T101_09 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual/Quad/Octal TDM-over-Packet Chip |
發布緊急采購，3分鐘左右您將得到回復。