- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63653F 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 PDF資料下載
參數資料
| 型號： | S1C63653F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 |
| 封裝： | CERAMIC, QFP15-100 |
| 文件頁數： | 66/121頁 |
| 文件大?。?/td> | 1127K |
| 代理商： | S1C63653F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁
S1C63653 TECHNICAL MANUAL
EPSON
41
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Output Ports)
4.6.3 High impedance control
The output ports can be set into a high impedance status. This control is done using the high impedance
control registers.
The high impedance control registers are provided to correspond with the output ports as shown below.
High impedance control register
Corresponding output port
R00HIZ
R00 (1 bit)
R01HIZ
R01 (1 bit)
R02HIZ
R02 (1 bit)
R03HIZ
R03 (1 bit)
When "1" is written to the high impedance control register, the corresponding output port terminal goes
into high impedance status. When "0" is written, the port outputs a signal according to the data register.
4.6.4 Special output
In addition to the regular DC output, special output can be selected for the output ports R02 and R03 as
shown in Table 4.6.4.1 with the software.
Figure 4.6.4.1 shows the configuration of the R02 and R03 output ports.
Table 4.6.4.1 Special output
Terminal
R03
R02
Special output
FOUT
TOUT
Output control register
FOUTE
PTOUT
Data
bus
Register
PTOUT
Register
R02
TOUT
R02
(TOUT)
Register
FOUTE
Register
R03
Register
R03HIZ
Register
R02HIZ
FOUT
R03
(FOUT)
Fig. 4.6.4.1 Configuration of R02 and R03 output ports
At initial reset, the output port data register is set to "0" and the high impedance control register is set to
"0". Consequently, the output terminal goes low (VSS).
When using the output port (R02, R03) as the special output port, fix the data register (R02, R03) at "1"
and the high impedance control register (R02HIZ, R03HIZ) at "0" (data output). The respective signal
should be turned on and off using the special output control register.
Note: Be aware that the output terminal is fixed at a low (VSS) level the same as the DC output if "0" is
written to the R02 and R03 registers when the special output has been selected.
Be aware that the output terminal shifts into high impedance status when "1" is written to the
high impedance control register (R02HIZ, R03HIZ).
相關PDF資料 |
PDF描述 |
|---|---|
| S1C6F567D0A0100 | MICROCONTROLLER, UUC141 |
| S1C6N3B0D0A0100 | MICROCONTROLLER, UUC54 |
| S1C6P366D0A0100 | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
| S1C6P466D0A0A00 | MICROCONTROLLER, UUC140 |
| S1C6S2L7D | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63656 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63657 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63658 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63666 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63709 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。