參數資料
型號: MC68HC05CJ4FB
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44
封裝: QFP-44
文件頁數: 72/114頁
文件大小: 361K
代理商: MC68HC05CJ4FB
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁當前第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
GENERAL RELEASE SPECIFICATION
MC68HC(7)05CJ4
SERIAL PERIPHERAL INTERFACE
MOTOROLA
Rev. 2.1
9-3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
9.2.4 Slave Select (SS)
In slave mode, the slave select (SS input) is generated by the master (parallel port
may be used) and used to “enable one” of several slaves to accept and/or return
data or “enable several” slaves to accept data. To insure a data byte transfer, the
SS signal must be low prior to occurrence of SCK1 and must not become high until
after the 8th (last) SCK1 cycle. Figure 9-2 shows the clock (SCK1) and data
relationship. Depending on the state of the CPHA control bit, the SS pin pulled low:
(1) allows the first bit of data onto the MISO system line for transfer and (2)
prevents the slave from reading or writing the data register. A further description of
the effect of the (SS) pin and (CPHA) control bit on the I/O data register is given in
the description of the (WCOL) status flag. The (WCOL) flag warns the slave if it has
had a conflict between a transmission and a write of the data register. A high level
on SS forces MISO to the high-impedance state. Also, SCK1 and MOSI are
ignored by the disabled slave.
In master mode, slave select (SS) input is monitored to assure that it stays false
(high). If slave select becomes true, the device immediately exits the master mode
and becomes a slave (MSTR = 0). Also, control bit (SPE) is forced to a zero
causing all SPI system pins to be inputs. An interrupt flag (MODF) is set warning
the device that the above events have occurred. The significance of this is that a
collision has occurred; that is, two devices have both become masters. This is
normally the result of software error, although some systems may allow the default
master to “knock all other masters off the bus” if an erroneous bus state is detected.
This is, of course, a catastrophic event and it is the responsibility of the default
master to completely “clean up” the system.
相關PDF資料
PDF描述
MC68HC05CL48 8-BIT, MROM, 1.802 MHz, MICROCONTROLLER, PQFP112
MC68HC705CL48 8-BIT, OTPROM, 1.802 MHz, MICROCONTROLLER, PQFP112
MC68HC05CT4FN 8-BIT, MROM, 2.048 MHz, MICROCONTROLLER, PQCC44
MC68HC05CT4FB 8-BIT, MROM, 2.048 MHz, MICROCONTROLLER, PQFP44
MC68HC05E16CB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56
相關代理商/技術參數
參數描述
MC68HC05CT4FB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification
MC68HC05CT4FN 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification
MC68HC05D9 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-bit microcomputer with PWM outputs and LED drive
MC68HC05E0 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit
MC68HC05E0FN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller