參數資料
型號： MC68HC05CJ4FB
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44
封裝： QFP-44
文件頁數： 70/114頁
文件大?。?/td> 361K
代理商： MC68HC05CJ4FB
GENERAL RELEASE SPECIFICATION
MOTOROLA
SERIAL PERIPHERAL INTERFACE
MC68HC(7)05CJ4
9-2
Rev. 2.1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
9.2.2 Serial Data In (MOSI)
In slave mode, MOSI is the signal used to receive data from some master device.
Figure 9-2 shows the serial clock and data timing relationship.
It should be noted that when a master device transmits data to a second device via
the MOSI line, the slave device (if it has the capability) will respond by sending data
into the MISO pin of the master device. This implies full duplex transmission with
both data out and data in synchronized to the same clock signal which is provided
by the master. Moreover, the SAME shift register is used for data out and data in.
Thus, the byte transmitted is replaced by the byte received, removing the need for
separate status bits for XMIT EMPTY and REC FULL. A single status bit, SPIF, is
used to signify I/O operation complete.
In the master mode, as noted above, the functions of MOSI and MISO are
inverted. The MOSI pin becomes the data output pin when the device is in the
master mode. When a transfer of data is not taking place with a slave device the
master drives the MOSI line high. The master always allows the data onto the
MOSI pin a half-cycle before the clock edge (SCK1) needed for the slave to latch
the data internally.
9.2.3 Serial Clock In/Out (SCK1)
In slave mode, the serial clock is used to move data both in and out of the device
through its MOSI and MISO pins. The master and slave devices are capable of
exchanging a byte of information during a sequence of eight clock pulses if wired
to do so. In the slave mode, the SCK1 pin becomes an input being sent from the
master device for the external clock. In this case SCK1 is asynchronous to the
slave device’s phase 1-2 clocks and read/write control, therefore synchronization
must take place prior to transmission and after reception. This must be done on the
byte level. The type of clock and its relationship with the data is controlled by bits
CPOL and CPHA. Reference Figure 9-2. The clock rate control bits SPR1 and
SPR0 have no function while the part is in the slave mode.
In master mode, the clock is generated within the master device by a circuit driven
from the bus clock. The clock rate is selected by bits (SPR1, SPR0) in the control
register. The SCK1 pin on the master device becomes a fixed output providing the
system clock to an enabled slave or slaves. The clock is used by the master to latch
incoming slave data on the MISO pin and shift out data to the slave device on the
MOSI pin. The master and slave must be operated in the same timing mode. The
type of clock and its relationship with the data is controlled by bits CPOL and
CPHA. Reference Figure 9-2.
相關PDF資料
PDF描述
MC68HC05CL48 8-BIT, MROM, 1.802 MHz, MICROCONTROLLER, PQFP112
MC68HC705CL48 8-BIT, OTPROM, 1.802 MHz, MICROCONTROLLER, PQFP112
MC68HC05CT4FN 8-BIT, MROM, 2.048 MHz, MICROCONTROLLER, PQCC44
MC68HC05CT4FB 8-BIT, MROM, 2.048 MHz, MICROCONTROLLER, PQFP44
MC68HC05E16CB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56
相關代理商/技術參數
參數描述
MC68HC05CT4FB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification
MC68HC05CT4FN 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification
MC68HC05D9 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-bit microcomputer with PWM outputs and LED drive
MC68HC05E0 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit
MC68HC05E0FN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*