參數資料
型號： DS21554LN
廠商： DALLAS SEMICONDUCTOR
元件分類： Digital Transmission Interface
英文描述： DATACOM, PCM TRANSCEIVER, PQFP100
封裝： 14 X 14 MM, LQFP-100
文件頁數： 78/117頁
文件大小： 698K
代理商： DS21554LN
DS21354 & DS21554
63 of 117
15.4 HDLC Register Description
HCR: HDLC CONTROL REGISTER (Address=B0 Hex)
(MSB)
(LSB)
–
RHR
TFS
THR
TABT
TEOM
TZSD
TCRCD
SYMBOL
POSITION NAME AND DESCRIPTION
–
HCR.7
Not Assigned. Should be set to zero when written.
RHR
HCR.6
Receive HDLC Reset. A 0 to 1 transition will reset the HDLC controller.
Must be cleared and set again for a subsequent reset.
TFS
HCR.5
Transmit Flag/Idle Select.
0 = 7Eh
1 = FFh
THR
HCR.4
Transmit HDLC Reset. A 0 to 1 transition will reset the HDLC
controller. Must be cleared and set again for a subsequent reset.
TABT
HCR.3
Transmit Abort. A 0 to 1 transition will cause the FIFO contents to be
dumped and one FEh abort to be sent followed by 7Eh or FFh flags/idle
until a new packet is initiated by writing new data into the FIFO. Must be
cleared and set again for a subsequent abort to be sent.
TEOM
HCR.2
Transmit End of Message. Should be set to a one just before the last data
byte of a HDLC packet is written into the transmit FIFO at THFR. This bit
will be cleared by the HDLC controller when the last byte has been
transmitted.
TZSD
HCR.1
Transmit Zero Stuffer Defeat. Overrides internal enable.
0 = enable the zero stuffer (normal operation)
1 = disable the zero stuffer
TCRCD
HCR.0
Transmit CRC Defeat.
0 = enable CRC generation (normal operation)
1 = disable CRC generation
HSR: HDLC STATUS REGISTER (Address=B1 Hex)
(MSB)
(LSB)
FRCL
RPE
RPS
RHALF
RNE
THALF
TNF
TMEND
SYMBOL
POSITION NAME AND DESCRIPTION
FRCL
HSR.7
Framer Receive Carrier Loss. Set when 255 (or 2048 if CCR3.0 = 1)
consecutive zeros have been detected at RPOSI and RNEGI.
RPE
HSR.6
Receive Packet End. Set when the HDLC controller detects either the
finish of a valid message (i.e., CRC check complete) or when the
controller has experienced a message fault such as a CRC checking error,
or an overrun condition, or an abort has been seen. The setting of this bit
prompts the user to read the RHIR register for details.
RPS
HSR.5
Receive Packet Start. Set when the HDLC controller detects an opening
byte. The setting of this bit prompts the user to read the RHIR register for
details.
相關PDF資料
PDF描述
DS2155G DATACOM, FRAMER, PBGA100
DS21600SN PLL BASED CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16
DS21600N PLL BASED CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDIP8
DS2155LN DATACOM, FRAMER, PQFP100
DS21602N PLL BASED CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDIP8
相關代理商/技術參數
參數描述
DS21554LN+ 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2155DK 功能描述:網絡開發工具 RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
DS2155G 功能描述:網絡控制器與處理器 IC T1/E1/J1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2155G/T&R 制造商:Maxim Integrated Products 功能描述:DS2155 T1/E1/J1 SCT 100P CSBGA T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LIU T1/E1/J1 SCT 100P CSBGA 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1/E1/J1 Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*