- 您現在的位置：買賣IC網 > PDF目錄15530 > EVAL-ADUC7023QSPZ1 (Analog Devices Inc)BOARD EVAL FOR ADUC7023 PDF資料下載
參數資料
| 型號： | EVAL-ADUC7023QSPZ1 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 70/96頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADUC7023 |
| 標準包裝： | 1 |
| 系列： | QuickStart™ PLUS 套件 |
| 類型： | MCU |
| 適用于相關產品： | ADuC7023 |
| 所含物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁當前第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
ADuC7023
Data Sheet
| Page 72 of 96
Table 85. PWMCON1 MMR Bit Designations
Bit
Name
Description
14
SYNC
Enables PWM synchronization.
Set to 1 by the user so that all PWM counters are reset on the next clock edge after the detection of a high-to-low
transition on the P2.2/SYNC pin.
Cleared by the user to ignore transitions on the P2.2/SYNC pin.
13
Reserved
Set to 0 by the user.
12
PWM3INV
Set to 1 by the user to invert PWM3.
Cleared by the user to use PWM3 in normal mode.
11
PWM1INV
Set to 1 by the user to invert PWM1.
Cleared by the user to use PWM1 in normal mode.
10
PWMTRIP
Set to 1 by the user to enable PWM trip interrupt. When the PWM trip input (Pin P1.5/PWMTRIPINPUT) is low, the
PWMEN bit is cleared and an interrupt is generated.
Cleared by the user to disable the PWMTRIP interrupt.
9
ENA
If HOFF = 0 and HMODE = 1. Note that, if not in H-bridge mode, this bit has no effect.
Set to 1 by the user to enable PWM outputs.
Cleared by the user to disable PWM outputs.
If HOFF = 1 and HMODE = 1, see Table 86.
8 to 6
PWMCP[2:0]
PWM clock prescaler bits. Sets the UCLK divider.
[000] = UCLK/2.
[001] = UCLK/4.
[010] = UCLK/8.
[011] = UCLK/16.
[100] = UCLK/32.
[101] = UCLK/64.
[110] = UCLK/128.
[111] = UCLK/256.
5
POINV
Set to 1 by the user to invert all PWM outputs.
Cleared by the user to use PWM outputs as normal.
4
HOFF
High side off.
Set to 1 by the user to force PWM0 and PWM2 outputs high. This also forces PWM1 and PWM3 low.
Cleared by the user to use the PWM outputs as normal.
3
LCOMP
Load compare registers.
Set to 1 by the user to load the internal compare registers with the values in PWMxCOMx on the next transition of
the PWM timer from 0x00 to 0x01.
Cleared by the user to use the values previously stored in the internal compare registers.
2
DIR
Direction control.
Set to 1 by the user to enable PWM0 and PWM1 as the output signals while PWM2 and PWM3 are held low.
Cleared by the user to enable PWM2 and PWM3 as the output signals while PWM0 and PWM1 are held low.
1
HMODE
Enables H-bridge mode.1
Set to 1 by the user to enable H-bridge mode.
Cleared by the user to operate the PWMs in standard mode.
0
PWMEN
Set to 1 by the user to enable all PWM outputs.
Cleared by the user to disable all PWM outputs.
1 In H-bridge mode, HMODE = 1. See Table 86 to determine the PWM outputs.
Rev. E
相關PDF資料 |
PDF描述 |
|---|---|
| AIUR-10-182K | INDUCTOR POWER 1800UH 10% T/H |
| EYM15DRSD | CONN EDGECARD 30POS DIP .156 SLD |
| V300C3V3C50B | CONVERTER MOD DC/DC 3.3V 50W |
| AIUR-06-271K | INDUCTOR POWER 270UH 10% T/H |
| EGM15DRSD | CONN EDGECARD 30POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADuC7023QSPZ2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI MCU with Enhanced IRQ Handler |
| EVALADUC7023QSPZU1 | 制造商:Analog Devices 功能描述: |
| EVAL-ADUC7024QS | 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk |
| EVAL-ADUC7024QS-U2 | 制造商:Analog Devices 功能描述:QUICK START DEVL SYST EVAL BOARD I.C. - Bulk |
| EVAL-ADUC7024QS-U3 | 制造商:Analog Devices 功能描述:ARM7 ADUC7024 QUICKSTART DEV KIT |
發布緊急采購，3分鐘左右您將得到回復。