參數資料
型號： PI7C8150BNDIE
廠商： Pericom
文件頁數： 18/109頁
文件大小： 0K
描述： IC PCI-PCI BRIDGE ASYNC 256-PBGA
標準包裝： 90
系列： *
應用： *
接口： *
電源電壓： *
封裝/外殼： 256-BGA
供應商設備封裝： 256-PBGA（17x17）
包裝： 管件
安裝類型： 表面貼裝
PI7C8150B
ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 16 of 109
April 2009 – Revision 1.08
Name
Pin #
Type
Description
S_CLKIN
21
H3
I
Secondary Clock Input: Provides timing for all
transactions on the secondary interface.
S_CLKOUT[9:0]
42, 41, 39, 38, 36,
35, 33, 32, 30, 29
M3, M2, N1,
L4, L3, M1, L2,
L1, K3, K2
O
Secondary Clock Output: Provides secondary clocks
phase synchronous with the P_CLK in synchronous
mode.
When these clocks are used, one of the clock outputs
must be fed back to S_CLKIN. Unused outputs may be
disabled by:
1. Writing the secondary clock disable bits in the
configuration space
2. Using the serial disable mask using the GPIO pins and
MSK_IN
3. Terminating them electrically.
In asynchronous mode, S_CLKOUT[5:0] are derived
from MSK_IN / ASYNC_CLKIN (please see CFG66 /
SCAN_EN_H / CLK_RATE pin description).
2.2.4
MISCELLANEOUS SIGNALS
Name
Pin #
Type
Description
MSK_IN /
ASYNC_CLKIN
126
K15
I
This is a multiplexed pin that is MSK_IN in
synchronous mode and ASYNC_CLK_IN in
asynchronous mode. This pin has a weak internal pull-
down resistor.
MSK_IN - Secondary Clock Disable Serial Input
(synchronous mode): This pin is used by PI7C8150B to
disable secondary clock outputs. The serial stream is
received by MSK_IN, starting when P_RESET is
detected deasserted and S_RESET_L is detected as
being asserted. The serial data is used for selectively
disabling secondary clock outputs and is shifted into the
secondary clock control configuration register. This pin
can be tied LOW to enable all secondary clock outputs
or tied HIGH to drive all the secondary clock outputs
HIGH.
ASYNC_CLKIN – Secondary Clock Input
(asynchronous mode): The asynchronous clock for the
secondary interface should be connected to this pin in
asynchronous mode. S_CLKOUT[9:0] will be derived
from ASYNC_CLKIN.
P_VIO
124
K14
I
Primary I/O Voltage: This pin is used to determine
either 3.3V or 5V signaling on the primary bus. P_VIO
must be tied to 3.3V only when all devices on the
primary bus use 3.3V signaling. Otherwise, P_VIO is
tied to 5V.
S_VIO
135
G14
I
Secondary I/O Voltage: This pin is used to determine
either 3.3V or 5V signaling on the secondary bus.
S_VIO must be tied to 3.3V only when all devices on
the secondary bus use 3.3V signaling. Otherwise, S_VIO
is tied to 5V.
BPCCE
44
N2
I
Bus/Power Clock Control Management Pin: When
this pin is tied HIGH and the PI7C8150B is placed in the
D3HOT power state, it enables the PI7C8150B to place
the secondary bus in the B2 power state. The secondary
clocks are disabled and driven to 0. When this pin is tied
LOW, there is no effect on the secondary bus clocks
when the PI7C8150B enters the D3HOT power state.
相關PDF資料
PDF描述
PI7C8152BMAIE IC PCI-PCI BRIDGE 2PORT 160-MQFP
PI7C8154ANAE IC PCI-PCI BRIDGE ASYNC 304-PBGA
PI7C8154BNAIE IC PCI-PCI BRIDGE ASYNC 304-PBGA
PI7C9X110BNBE IC PCIE TO PCI REV BRG 160LFBGA
PI7C9X130DNDE IC PCIE-PCIX BRIDGE 1PORT 256BGA
相關代理商/技術參數
參數描述
PI7C8150BNDIE-33 功能描述:外圍驅動器與原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150DMAE 功能描述:外圍驅動器與原件 - PCI 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150DND 制造商:Pericom Semiconductor Corporation 功能描述:BRIDGE 制造商:Pericom Semiconductor Corporation 功能描述:2 PORT PCI BRIDGE - Rail/Tube
PI7C8150DNDE 功能描述:外圍驅動器與原件 - PCI 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150EVB 功能描述:界面開發工具 2 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*