參數資料
型號： PI7C8150BNDIE
廠商： Pericom
文件頁數： 107/109頁
文件大?。?/td> 0K
描述： IC PCI-PCI BRIDGE ASYNC 256-PBGA
標準包裝： 90
系列： *
應用： *
接口： *
電源電壓： *
封裝/外殼： 256-BGA
供應商設備封裝： 256-PBGA（17x17）
包裝： 管件
安裝類型： 表面貼裝
PI7C8150B
ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 97 of 109
April 2009 – Revision 1.08
read data. Again, the PAR signal corresponds to read data from the previous data phase
cycle.
15.2.3
REPORTING PARITY ERRORS
For all address phases, if a parity error is detected, the error should be reported on the
P_SERR_L signal by asserting P_SERR_L for one cycle and then 3-stating two cycles
after the bad address. P_SERR_L can only be asserted if bit 6 and 8 in the Command
Register are both set to 1. For write data phases, a parity error should be reported by
asserting the P_PERR_L signal two cycles after the data phase and should remain asserted
for one cycle when bit 6 in the Command register is set to a 1.
The target reports any type of data parity errors during write cycles, while the master
reports data parity errors during read cycles.
Detection of an address parity error will cause the PCI-to-PCI Bridge target to not claim
the bus (P_DEVSEL_L remains inactive) and the cycle will then terminate with a Master
Abort. When the bridge is acting as master, a data parity error during a read cycle results in
the bridge master initiating a Master Abort.
15.2.4
SECONDARY IDSEL MAPPING
When PI7C8150B detects a Type 1 configuration transaction for a device connected to
the secondary, it translates the Type 1 transaction to Type 0 transaction on the downstream
interface. Type 1 configuration format uses a 5-bit field at P_AD[15:11] as a device
number. This is translated to S_AD[31:16] by PI7C8150B.
16
IEEE 1149.1 COMPATIBLE JTAG CONTROLLER
An IEEE 1149.1 compatible Test Access Port (TAP) controller and associated TAP pins
are provided to support boundary scan in PI7C8150B for board-level continuity test and
diagnostics. The TAP pins assigned are TCK, TDI, TDO, TMS and TRST_L. All digital
input, output, input/output pins are tested except TAP pins.
The IEEE 1149.1 Test Logic consists of a TAP controller, an instruction register, and
a group of test data registers including Bypass and Boundary Scan registers. The TAP
controller is a synchronous 16-state machine driven by the Test Clock (TCK) and the Test
Mode Select (TMS) pins. An independent power on reset circuit is provided to ensure the
machine is in TEST_LOGIC_RESET state at power-up. The JTAG signal lines are not
active when the PCI resource is operating PCI bus cycles.
PI7C8150B implements 3 basic instructions: BYPASS, SAMPLE/PRELOAD, and
EXTEST.
16.1
BOUNDARY SCAN ARCHITECTURE
Boundary-scan test logic consists of a boundary-scan register and support logic. These are
accessed through a Test Access Port (TAP). The TAP provides a simple serial interface
相關PDF資料
PDF描述
PI7C8152BMAIE IC PCI-PCI BRIDGE 2PORT 160-MQFP
PI7C8154ANAE IC PCI-PCI BRIDGE ASYNC 304-PBGA
PI7C8154BNAIE IC PCI-PCI BRIDGE ASYNC 304-PBGA
PI7C9X110BNBE IC PCIE TO PCI REV BRG 160LFBGA
PI7C9X130DNDE IC PCIE-PCIX BRIDGE 1PORT 256BGA
相關代理商/技術參數
參數描述
PI7C8150BNDIE-33 功能描述:外圍驅動器與原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150DMAE 功能描述:外圍驅動器與原件 - PCI 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150DND 制造商:Pericom Semiconductor Corporation 功能描述:BRIDGE 制造商:Pericom Semiconductor Corporation 功能描述:2 PORT PCI BRIDGE - Rail/Tube
PI7C8150DNDE 功能描述:外圍驅動器與原件 - PCI 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150EVB 功能描述:界面開發工具 2 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*