參數資料
型號： PI7C8150BNDIE
廠商： Pericom
文件頁數： 109/109頁
文件大?。?/td> 0K
描述： IC PCI-PCI BRIDGE ASYNC 256-PBGA
標準包裝： 90
系列： *
應用： *
接口： *
電源電壓： *
封裝/外殼： 256-BGA
供應商設備封裝： 256-PBGA（17x17）
包裝： 管件
安裝類型： 表面貼裝
PI7C8150B
ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 99 of 109
April 2009 – Revision 1.08
The instruction determines the test to be performed, the test data register to be accessed, or
both. The IR is two bits wide. When the IR is selected, the most significant bit is connected
to TDI, and the least significant bit is connected to TDO. The value presented on the TDI
pin is shifted into the IR on each rising edge of TCK. The TAP controller captures fixed
parallel data (1101 binary). When a new instruction is shifted in through TDI, the value
1101(binary) is always shifted out through TDO, least significant bit first. This helps
identify instructions in a long chain of serial data from several devices.
Upon activation of the TRST_L reset pin, the latched instruction asynchronously changes
to the id code instruction. When the TAP controller moves into the test state other than by
reset activation, the opcode changes as TDI shifts, and becomes active on the falling edge
of TCK.
16.2
BOUNDARY SCAN INSTRUCTION SET
The PI7C8150B supports three mandatory boundary-scan instructions (BYPASS,
SAMPLE and EXTEST). The table shown below lists the PI7C8150B’s boundary-scan
instruction codes.
Table 16-1. TAP Pins
Instruction
/
Requisite
Opcode (binary)
Description
EXTEST
IEEE 1149.1
Required
00000
EXTEST initiates testing of external circuitry, typically board-
level interconnects and off chip circuitry. EXTEST connects the
boundary-scan register between TDI and TDO. When EXTEST
is selected, all output signal pin values are driven by values
shifted into the boundary-scan register and may change only of
the falling edge of TCK. Also, when EXTEST is selected, all
system input pin states must be loaded into the boundary-scan
register on the rising-edge of TCK.
SAMPLE
IEEE 1149.1
Required
0001
SAMPLE performs two functions:
A snapshot of the sample instruction is captured on the
rising edge of TCK without interfering with normal
operation. The instruction causes boundary-scan register
cells associated with outputs to sample the value being
driven.
On the falling edge of TCK, the data held in the boundary-
scan cells is transferred to the slave register cells.
Typically, the slave latched data is applied to the system
outputs via the EXTEST instruction.
INTSCAN
00010
Enable internal SCAN test
CLAMP
00100
CLAMP instruction allows the state of the signals driven from
component pins to be determined from the boundary-scan
register while the bypass register is selected as the serial path
between TDI and TDO. The signal driven from the component
pins will not change while the CLAMP instruction is selected.
BYPASS
11111
BYPASS instruction selects the one-bit bypass register between
TDI and TDO pins. 0 (binary) is the only instruction that
accesses the bypass register. While this instruction is in effect,
all other test data registers have no effect on system operation.
Test data registers with both test and system functionality
performs their system functions when this instruction is selected.
相關PDF資料
PDF描述
PI7C8152BMAIE IC PCI-PCI BRIDGE 2PORT 160-MQFP
PI7C8154ANAE IC PCI-PCI BRIDGE ASYNC 304-PBGA
PI7C8154BNAIE IC PCI-PCI BRIDGE ASYNC 304-PBGA
PI7C9X110BNBE IC PCIE TO PCI REV BRG 160LFBGA
PI7C9X130DNDE IC PCIE-PCIX BRIDGE 1PORT 256BGA
相關代理商/技術參數
參數描述
PI7C8150BNDIE-33 功能描述:外圍驅動器與原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150DMAE 功能描述:外圍驅動器與原件 - PCI 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150DND 制造商:Pericom Semiconductor Corporation 功能描述:BRIDGE 制造商:Pericom Semiconductor Corporation 功能描述:2 PORT PCI BRIDGE - Rail/Tube
PI7C8150DNDE 功能描述:外圍驅動器與原件 - PCI 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C8150EVB 功能描述:界面開發工具 2 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*