參數資料
型號： 935270538118
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
封裝： 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64
文件頁數： 52/93頁
文件大?。?/td> 2118K
代理商： 935270538118
Philips Semiconductors
ISP1160
Embedded USB Host Controller
Product data
Rev. 03 — 27 February 2003
56 of 89
9397 750 10765
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
8
PPS
(read) PortPowerStatus: This bit reects the port power status,
regardless of the type of power switching implemented. This bit is
cleared if an overcurrent condition is detected.
The HCD sets this bit by writing SetPortPower or SetGlobalPower.
The HCD clears this bit by writing ClearPortPower or
ClearGlobalPower. Which power control switches are enabled is
determined by PowerSwitchingMode.
In the global switching mode (PowerSwitchingMode = 0), only
Set/ClearGlobalPower controls this bit. In per-port power switching
(PowerSwitchingMode = 1), if the PortPowerControlMask[NDP] bit
for the port is set, only Set/ClearPortPower commands are
enabled. If the mask is not set, only Set/ClearGlobalPower
commands are enabled.
When port power is disabled, CurrentConnectStatus,
PortEnableStatus, PortSuspendStatus, and PortResetStatus
should be reset.
0 — port power is off
1 — port power is on
(write) SetPortPower: The HCD writes a logic 1 to set the
PortPowerStatus bit. Writing a logic 0 has no effect.
Remark: This bit always reads logic 1 if power switching is not
supported.
7 to 5
-
reserved
4
PRS
(read) PortResetStatus: When this bit is set by a write to
SetPortReset, port reset signaling is asserted. When reset is
completed, this bit is cleared when PortResetStatusChange is set.
This bit cannot be set if CurrentConnectStatus is cleared.
0 — port reset signal is not active
1 — port reset signal is active
(write) SetPortReset: The HCD sets the port reset signaling by
writing a logic 1 to this bit. Writing a logic 0 has no effect. If
CurrentConnectStatus is cleared, this write does not set
PortResetStatus but instead sets ConnectStatusChange. This
informs the driver that it attempted to reset a disconnected port.
3
POCI
(read) PortOverCurrentIndicator: This bit is valid only when the
Root Hub is congured in such a way that overcurrent conditions
are reported on a per-port basis. If per-port overcurrent reporting
is not supported, this bit is set to logic 0. If cleared, all power
operations are normal for this port. If set, an overcurrent condition
exists on this port. This bit always reects the overcurrent input
signal.
0 — no overcurrent condition
1 — overcurrent condition detected
(write) ClearSuspendStatus: The HCD writes a logic 1 to initiate
a resume. Writing a logic 0 has no effect. A resume is initiated only
if PortSuspendStatus is set.
Table 35:
HcRshPortStatus[1:2] register: bit description…continued
Bit
Symbol
Description
相關PDF資料
PDF描述
935270523557 UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
935270668112 POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PDSO48
935272535118 POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PBGA56
935272535157 POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PBGA56
935268661112 POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PDSO48
相關代理商/技術參數
參數描述
935270713557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP
935270792551 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270792557 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270793551 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
935270793557 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*