- 您現在的位置：買賣IC網 > PDF目錄374613 > S-7600A (Seiko Instruments Inc.) Hardware Specification (TCP/IP Network Stack LSI) PDF資料下載
參數資料
| 型號： | S-7600A |
| 廠商： | Seiko Instruments Inc. |
| 英文描述： | Hardware Specification (TCP/IP Network Stack LSI) |
| 中文描述： | 硬件規格（TCP / IP網絡堆棧大規模集成電路） |
| 文件頁數： | 45/60頁 |
| 文件大?。?/td> | 371K |
| 代理商： | S-7600A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
TCP/IP Network Stack LSI
S-7600A
Hardware Specification
Revision 1.3
Seiko Instruments Inc.
7-18
Table 7-40
Socket Interrupt High Register Description
Bit
Bit Name
Access
Description
7
URG
R/W
This interrupt is generated when urgent data arrives.
The system interface should read the
Urgent Data
Pointer
register to see the location of the data. Writing
a “1” to this bit clears the interrupt.
6
RST
R/W
This interrupt is generated when a TCP peer sends
the socket RST flag indicating that the current TCP
session is not valid. Writing a “1” to this bit clears this
interrupt. When this condition occurs, the hardware no
longer operates and re-initializing the socket is
recommended.
5
Term
R/W
This interrupt is generated when the socket
connection is terminated and a TCP FIN flag is
received. Writing a “1” to this bit clears the interrupt.
4
ConU
R/W
This interrupt is generated when a connection is
established. Writing a “1” to this bit clears the
interrupt.
7.3.23. Socket Data Register (0x2E)
(Memory Mapped Read/Write, Default 0x00)
This register is used by a system controller to read incoming data packets and write outgoing data. Data
transmissions start for TCP connections only after a write occurs at 0x30.
7.3.24. TCP Data Send and Buffer Out Length Registers (0x30-0x31)
(Read/Write, Default 0x03FF)
When read, these registers report the amount of space available in the outgoing buffer. Register 0x30
stores the least significant byte; 0x31 stores the most significant byte. Writing any data to 0x30 causes
data transmissions to start on TCP connections.
7.3.25. Buffer In Length Registers (0x32-0x33)
(Read-Only, Default 0x0000)
These read-only registers report the amount of data available in the received data buffer. 0x32 stores the
least significant byte; 0x33 stores the most significant byte.
7.3.26. Urgent Data Pointer Registers (0x34-0x35)
(Read-Only, Default 0x0000)
These read-only registers report the offset to the start of urgent data (as marked through the TCP
header) relative to the incoming data buffer. Register 0x34 stores the least significant byte; 0x35 stores
the most significant byte.
相關PDF資料 |
PDF描述 |
|---|---|
| S-80230AG | NEGATIVE VOLTAGE REGULATOR |
| S-80230AG-GA-S | NEGATIVE VOLTAGE REGULATOR |
| S-80230AG-GA-T1 | NEGATIVE VOLTAGE REGULATOR |
| S-80230AG-GA-T2 | NEGATIVE VOLTAGE REGULATOR |
| S-80250AG | NEGATIVE VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S760BK | 功能描述:直流電源連接器 LOCKING MINI PWR PLG WHITE 0.080" 2.0mm RoHS:否 制造商:Kycon 產品:Receptacles 觸點內徑: 觸點外徑: 中心腳長度: 電流額定值:7.5 A 電壓額定值:20 V 安裝角:Right 安裝風格:Cable |
| S760BK-1MTR | 制造商:Switchcraft 功能描述:Locking 2.0mm DC Power Plug Cable 1m |
| S760K | 功能描述:直流電源連接器 DC PWR PLG 0.080" 1.7"L, BLK HAND. LCK RoHS:否 制造商:Kycon 產品:Receptacles 觸點內徑: 觸點外徑: 中心腳長度: 電流額定值:7.5 A 電壓額定值:20 V 安裝角:Right 安裝風格:Cable |
| S760K | 制造商:Switchcraft 功能描述:JACK PLUG DC |
| S76121P | 制造商:SUNTAC 制造商全稱:SUNTAC 功能描述:47A, 30V, 0.021 OHM, N-CHANNEL, LOGIC LEVEL ULTRAFET POWER MOSFETS |
發布緊急采購，3分鐘左右您將得到回復。