- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C6N3B0D0A0100 MICROCONTROLLER, UUC54 PDF資料下載
參數資料
| 型號： | S1C6N3B0D0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, UUC54 |
| 封裝： | DIE-54 |
| 文件頁數： | 24/79頁 |
| 文件大?。?/td> | 606K |
| 代理商： | S1C6N3B0D0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁
22
EPSON
S1C6N3B0 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIARCUITS AND OPERATION (Output Ports)
BUZZER, BUZZER (R01, R00)
The output ports R01 and R00 can be set to BUZZER output port and BUZZER output (BUZZER reverse
output) port, respectively.
Direct driving of piezo-electric buzzer
By setting the R01 to the BUZZER output port and the R00 to the BUZZER output port, these two termi-
nals can directly drive a piezo-electric buzzer. The BUZZER output (R00) can only be set if the R01 is set
to the BUZZER output.
The output signal polarity is a high level while the buzzer signal is off.
At initial reset, the output terminals go high.
When "0" is written to the BUZZER (R01)/BUZZER (R00) registers, the output terminals output the
buzzer signals. When "1" is written, the terminals go high.
Figure 4.4.3.3 shows the buzzer direct drive waveform.
R01(R00) register
BUZZER output waveform
10
1
Fig. 4.4.3.3 BUZZER output waveform (direct driving)
Single terminal driving of piezo-electric buzzer
The piezo-electric buzzer can be driven with one terminal by setting the R01 to the BUZZER output
terminal. In this case, the polarity of the buzzer off signal can also be selected from high level and low
level by mask option.
At initial reset, the buzzer output goes off and the output terminal (R01) is set to the level that is selected
by mask option.
When "0" is written to the BUZZER (R01) register, the output terminal outputs the buzzer signal.
Figure 4.4.3.4 shows the buzzer output waveform in single terminal driving.
R01 register
BUZZER output waveform (OFF level = HIGH)
BUZZER output waveform (OFF level = LOW)
10
1
Fig. 4.4.3.4 BUZZER output waveform (single terminal driving)
BUZZER frequency
The buzzer signal frequency can be selected from 2 types (fBZL, fBZH) using the XBZR register. The
frequencies are set as in Table 4.4.3.2 according to the model.
Table 4.4.3.2 BUZZER frequency
Buzzer frequency
fBZL (XBZR="1")
fBZH (XBZR="0")
Frequency
S1C6N3B0
Crystal oscillation
(32.768 kHz)
fOSC/16=2kHz
fOSC/8=4kHz
S1C6N3B0
CR oscillation
(65 kHz)
fOSC/16=4kHz
fOSC/8=8kHz
S1C6A3B0
Ceramic oscillation
fOSC/192
fOSC/96
S1C6A3B0
CR oscillation
fOSC/96
fOSC/48
相關PDF資料 |
PDF描述 |
|---|---|
| S1C6P366D0A0100 | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
| S1C6P466D0A0A00 | MICROCONTROLLER, UUC140 |
| S1C6S2L7D | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58 |
| S1C6S2A7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C6S2B7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C-6-S | 制造商:GRIPCO 功能描述: |
| S1C7309X | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C7309X01 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C88349 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88649 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。