- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C621C0D 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC74 PDF資料下載
參數資料
| 型號： | S1C621C0D |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC74 |
| 封裝： | DIE-74 |
| 文件頁數： | 48/108頁 |
| 文件大小： | 992K |
| 代理商： | S1C621C0D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
36
EPSON
S1C621C0 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (LCD Driver)
LDTY1, LDTY0: LCD drive duty selection (C0HD1, D0)
Sets the LCD drive duty as shown in Table 4.7.7.2.
Table 4.7.7.2 LCD drive duty setting
LDTY1
0
1
LDTY0
0
1
X
Duty
1/2
1/3
1/4
COM0, COM1
COM0–COM2
COM0–COM3
Frame frequency *
fOSC1/1,024 (32 Hz)
fOSC1/768 (42.7 Hz)
fOSC1/1,024 (32 Hz)
68 (34
× 2)
102 (34
× 3)
136 (34
× 4)
Terminals used
in common
Maximum number
of segments
* In case of fOSC1 = 32.768 kHz
At initial reset, these registers are set to "0".
LDMS: LCD display memory area selection (C0HD3)
Selects the display memory area.
When "1" is written:
Page 0 (R/W)
When "0" is written:
Page 4 (W)
Reading:
Valid
By writing "1" to LDMS, page 0 is selected and addresses 050H–07FH become the display memory. Since a
RAM has been allocated in this area, it can be used as the display memory for reading/writing.
When LDMS is set to "0", page 4 (450H–47FH) becomes the display memory. This area is write only.
At initial reset, this register is set to "0".
Display memory (50H–7FH)
The LCD segments are lit or turned off depending on this data.
When "1" is written:
Lit
When "0" is written:
Not lit
Reading:
Invalid
By writing data into the display memory allocated to the LCD segment (on the panel), the segment can be
lit or put out.
At initial reset, the contents of the display memory are undefined.
4.7.8 Programming notes
(1) The contents of the display memory are undefined until the area is initialized (through, for instance,
memory clear processing by the CPU). Initialize the display memory by executing initial processing.
(2) When page 4 is selected for the display memory area, since the display memory area is write-only,
display data cannot be rewritten by arithmetic operations (such as AND, OR, ADD, SUB).
(3) 100 msec or more time is necessary for stabilizing the LCD drive voltages VC1, VC2 and VC3 after setting
the LCD power control register LPWR to "1". Be careful of the segment-on right after the power is
turned on.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C62480D | 4-BIT, MROM, 2.3 MHz, MICROCONTROLLER, UUC135 |
| S1C62440F | 4-BIT, MROM, 2.3 MHz, MICROCONTROLLER, PQFP128 |
| S1C62740D | 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC109 |
| S1C62920D | 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC63 |
| S1C62A33D | 4-BIT, MROM, 0.6 MHz, MICROCONTROLLER, UUC86 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63004 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63008 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63016 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63158 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63408 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。