- 您現在的位置：買賣IC網 > PDF目錄379803 > CD1865 (Intel Corp.) Intelligent Eight-Channel Communications Controller PDF資料下載
參數資料
| 型號： | CD1865 |
| 廠商： | Intel Corp. |
| 英文描述： | Intelligent Eight-Channel Communications Controller |
| 中文描述： | 智能八通道通信控制器 |
| 文件頁數： | 81/150頁 |
| 文件大?。?/td> | 871K |
| 代理商： | CD1865 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁
Intelligent Eight-Channel Communications Controller
—
CD1865
Datasheet
81
are Local and Remote Loopback. Used together with diagnostic firmware in the host system, the
Loopback Modes provide very thorough test coverage of all CD1865 functional blocks: the
CD1865 processor, ROM, RAM, bus interface, transmitters/receivers, and random logic.
Local Loopback Mode
Local Loopback mode is a
‘
silent
’
loopback, for example, data being sent by the transmitter is
internally connected to the receiver without reaching the external TxD pin. Generally, this is
advantageous because it allows diagnostic software to operate without causing unwanted effects on
any remote device that may be connected to the serial line. During local loopback, the TxD pin is in
the
‘
mark
’
(a logic
‘
1
’
) state. If non-silent loopback is also needed, it can be easily implemented
externally with an AND gate or a jumper plug on the serial connector.
Local Loopback mode is invoked by setting the LLM bit in the Channel Option register 2 (COR2)
and then issuing a channel command to tell the CD1865 that COR2 has changed. When in this
mode, the channels TxD Output is internally looped back to the channel
’
s RxD Input. However, all
other channel parameters including modem pins continue to work independently and normally.
Receive special character recognition, overflow handling, and other options may be tested by using
the Local Loopback mode and transmitting the appropriate character sequences. As shown in
Figure 27 on page 82
, the loopback connection is directly from the TxD signal to the RxD signal,
for example, all transmit and receive logic is tested except the actual I/O buffers.
Remote Loopback Mode
Remote Loopback mode is provided to support testing of devices connected to the serial lines.
Remote Loopback is invoked by setting the RLM bit in the Channel Option register 2 (COR2).
When in this mode, the CD1865 echoes the received data to the transmitter for transmission back to
the sender. The received data is not passed on to the host.
When in Remote Loopback mode, the transmitter continues to run as defined by its own Baud Rate
registers, not the values being used by the receiver. The CD1865 receives a complete character,
strips off Start, Stop, and Parity bits, and then re-transmits it with Parity, Length, and Stop bit
Output options as defined in COR1. Thus, it is possible to change baud rate. However, this can
result in receiver overflow. In general, when programming for Remote Loopback Operation, the
Transmit bit rate should be as fast or slightly faster than the expected receive rate to avoid possible
overrun and loss of data. The number of Stop bits should be set to a one, rather than one-and-a-half
or two, if the application permits it. This ensures that the effective transmit rate is faster than the
receive rate.
As shown in
Figure 27
, Remote Loopback is done at the character level and not the bit level. The
Receive and Transmit FIFOs are not used in Remote Loopback. Characters are transferred directly
from the Receive Holding register to the Transmit Holding register. For a diagnostic mode that
tests the FIFOs, other logic is needed to be implemented by programming the host system to
transfer received characters from the Receive FIFO to the Transmit FIFO. This permits full testing
of FIFO thresholds, service request logic, special character operation, and so on.
相關PDF資料 |
PDF描述 |
|---|---|
| CD22100 | CMOS 4 x 4 Crosspoint Switch with Control Memory High-Voltage Type (20V Rating) |
| CD22100E | CMOS 4 x 4 Crosspoint Switch with Control Memory High-Voltage Type (20V Rating) |
| CD22100F | CMOS 4 x 4 Crosspoint Switch with Control Memory High-Voltage Type (20V Rating) |
| CD22101 | CMOS 4 x 4 x 2 Crosspoint Switch with Control Memory |
| CD22101E | CMOS 4 x 4 x 2 Crosspoint Switch with Control Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CD1865N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1865P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1866N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1866P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1867N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。