- 您現在的位置：買賣IC網 > PDF目錄166217 > AM54BDS128AGT89IT (ADVANCED MICRO DEVICES INC) SPECIALTY MEMORY CIRCUIT, PBGA93 PDF資料下載
參數資料
| 型號： | AM54BDS128AGT89IT |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 存儲器 |
| 英文描述： | SPECIALTY MEMORY CIRCUIT, PBGA93 |
| 封裝： | 10 X 10 MM, 0.80 PITCH, FBGA-93 |
| 文件頁數： | 26/71頁 |
| 文件大?。?/td> | 1031K |
| 代理商： | AM54BDS128AGT89IT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
July 23, 2002
Am54BDS128AG
32
ADV ANCE
I N FO RMAT I O N
FLASH WRITE OPERATION STATUS
The device provides several bits to determine the sta-
tus of a program or erase operation: DQ2, DQ3, DQ5,
DQ6, and DQ7. Table 15, “Write Operation Status,” on
page 35 and the following subsections describe the
function of these bits. DQ7 and DQ6 each offers a
method for determining whether a program or erase
operation is complete or in progress.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host sys-
tem whether an Embedded Program or Erase algo-
rithm is in progress or completed, or whether a bank is
in Erase Suspend. Data# Polling is valid after the ris-
ing edge of the final WE# pulse in the command se-
quence.
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum pro-
grammed to DQ7. This DQ7 status also applies to pro-
g r am mi ng d u rin g Era s e Sus p e nd. W hen th e
Embedded Program algorithm is complete, the device
outputs the datum programmed to DQ7. The system
must provide the program address to read valid status
information on DQ7. If a program address falls within a
protected sector, Data# Polling on DQ7 is active for
approximately 1 s, then that bank returns to the read
mode.
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the bank enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
The system must provide an address within any of the
sectors selected for erasure to read valid status infor-
mation on DQ7.
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data# Poll-
ing on DQ7 is active for approximately 100 s, then
the bank returns to the read mode. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the se-
lected sectors that are protected. However, if the sys-
tem reads DQ7 at an address within a protected
sector, the status may not be valid.
Just prior to the completion of an Embedded Program
or Erase operation, DQ7 may change asynchronously
with DQ6–DQ0 while Output Enable (OE#) is asserted
low. That is, the device may change from providing
status information to valid data on DQ7. Depending on
when the system samples the DQ7 output, it may read
the status or valid data. Even if the device has com-
pleted the program or erase operation and DQ7 has
valid data, the data outputs on DQ6–DQ0 may be still
invalid. Valid data on DQ7–DQ0 will appear on suc-
cessive read cycles.
Table 15 shows the outputs for Data# Polling on DQ7.
Figure 3 shows the Data# Polling algorithm. Figure 27,
(During Embedded Algorithm),” on page 58 in the AC
Characteristics section shows the Data# Polling timing
diagram.
Notes:
1. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the
sector being erased. During chip erase, a valid address is any non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5.
Figure 4.
Data# Polling Algorithm
DQ7 = Data?
Yes
No
DQ5 = 1?
No
Yes
FAIL
PASS
Read DQ7–DQ0
Addr = VA
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
START
相關PDF資料 |
PDF描述 |
|---|---|
| AM7200-65RC | 256 X 9 OTHER FIFO, 65 ns, PDIP28 |
| AM7200-80RC | 256 X 9 OTHER FIFO, 80 ns, PDIP28 |
| AM7201-25DC | 512 X 9 OTHER FIFO, 25 ns, CDIP28 |
| AM7203-65JC | 2K X 9 OTHER FIFO, 65 ns, PQCC32 |
| AM7831X | DUAL LINE DRIVER, UUC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM54S | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Four-Bit Shifter With Three-State Outputs |
| AM54S350 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Four-Bit Shifter With Three-State Outputs |
| AM-55 | 制造商:Amprobe Test Tools 功能描述:Digital Multimeter |
| AM-550 | 功能描述:數字萬用表 Digital Multimeter TRMS RoHS:否 制造商:Tektronix 產品:Multimeters 類型:Bench 準確性:0.04 % 電壓范圍:2 V to 2 kV 電阻范圍: 電容范圍: 顯示計數: 頻率:10 Hz to 45 Hz, 850 Hz to 1 MHz 測距: 真均方根值: 數據保持: |
| AM55-0001 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:140 mW Power Amplifier with T/R and Diversity Switches 2.42.5 GHz |
發布緊急采購，3分鐘左右您將得到回復。